- 您现在的位置：买卖IC网 > PDF目录18780 > SI4739-C40-GUR (Silicon Laboratories Inc)IC RX FM/WB RAD RDS/RBDS 24SSOP PDF资料下载
参数资料
| 型号： | SI4739-C40-GUR |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 24/42页 |
| 文件大小： | 0K |
| 描述： | IC RX FM/WB RAD RDS/RBDS 24SSOP |
| 标准包装： | 2,500 |
| 频率： | 520kHz ~ 1.71MHz，64MHz ~ 108MHz，162.4MHz ~ 162.55MHz |
| 调制或协议： | AM，FM，WB |
| 应用： | 通用 |
| 电流 - 接收： | 19.9mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 特点： | 配有 RSSI |
| 电源电压： | 2V ~ 5.5V |
| 工作温度： | -20°C ~ 85°C |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
Si4736/37/38/39-C40
5.13. Seek
Seek tuning will search up or down for a valid channel.
Valid channels are found when the receive signal
strength indicator (RSSI) and the signal-to-noise ratio
(SNR) values exceed the set threshold. Using the SNR
qualifier rather than solely relying on the more
traditional RSSI qualifier can reduce false stops and
increase the number of valid stations detected. Seek is
initiated using the FM_SEEK_START and
RST. The GPO1 pin includes an internal pull-up resistor,
which is connected while RST is low, and the GPO2 pin
includes an internal pull-down resistor, which is
connected while RST is low. Therefore, it is only
necessary for the user to actively drive pins which differ
from these states. See Table 14.
Table 14. Bus Mode Select on Rising Edge of
RST
AM_SEEK_START commands. The RSSI and SNR
threshold settings are adjustable using properties (see
Table 16).
5.14. Reference Clock
Bus Mode
2-Wire
SPI
3-Wire
GPO1
1
1
0 (must drive)
GPO2
0
1 (must drive)
0
The Si4736/37/38/39 reference clock is programmable,
supporting RCLK frequencies in Table 13. Refer to
Table 3, “DC Characteristics,” on page 5 for switching
voltage levels and Table 9, “FM Receiver
Characteristics,” on page 12 for frequency tolerance
information.
An onboard crystal oscillator is available to generate the
32.768 kHz reference when an external crystal and load
capacitors are provided. Refer to "2. Typical Application
Schematic (QFN)" on page 17. This mode is enabled
using the POWER_UP command. Refer to Table 15,
“Selected Si473x Commands,” on page 27.
The Si4736/37/38/39 performance may be affected by
data activity on the SDIO bus when using the integrated
internal oscillator. SDIO activity results from polling the
tuner for status or communicating with other devices
that share the SDIO bus. If there is SDIO bus activity
while the Si4736/37/38/39 is performing the seek/tune
function, the crystal oscillator may experience jitter,
which may result in mistunes, false stops, and/or lower
SNR.
For best seek/tune results, Silicon Laboratories
recommends that all SDIO data traffic be suspended
during Si4736/37/38/39 seek and tune operations. This
is achieved by keeping the bus quiet for all other
devices on the bus, and delaying tuner polling until the
tune or seek operation is complete. The seek/tune
complete (STC) interrupt should be used instead of
polling to determine when a seek/tune operation is
complete.
5.15. Control Interface
A serial port slave interface is provided, which allows an
external controller to send commands to the
Si4736/37/38/39 and receive responses from the
device. The serial port can operate in three bus modes:
2-wire mode, 3-wire mode, or SPI mode. The
Si4736/37/38/39 selects the bus mode by sampling the
state of the GPO1 and GPO2 pins on the rising edge of
After the rising edge of RST, the pins GPO1 and GPO2
are used as general purpose output (O) pins, as
described in Section “5.16. GPO Outputs”. In any bus
mode, commands may only be sent after V IO and V DD
supplies are applied.
In any bus mode, before sending a command or reading
a response, the user must first read the status byte to
ensure that the device is ready (CTS bit is high).
5.15.1. 2-Wire Control Interface Mode
When selecting 2-wire mode, the user must ensure that
SCLK is high during the rising edge of RST, and stays
high until after the first start condition. Also, a start
condition must not occur within 300 ns before the rising
edge of RST.
The 2-wire bus mode uses only the SCLK and SDIO
pins for signaling. A transaction begins with the START
condition, which occurs when SDIO falls while SCLK is
high. Next, the user drives an 8-bit control word serially
on SDIO, which is captured by the device on rising
edges of SCLK. The control word consists of a 7-bit
device address, followed by a read/write bit (read = 1,
write = 0). The Si4736/37/38/39 acknowledges the
control word by driving SDIO low on the next falling
edge of SCLK.
Although the Si4736/37/38/39 will respond to only a
single device address, this address can be changed
with the SEN pin (note that the SEN pin is not used for
signaling in 2-wire mode). When SEN = 0, the 7-bit
device address is 0010001b. When SEN = 1, the
address is 1100011b.
For write operations, the user then sends an 8-bit data
byte on SDIO, which is captured by the device on rising
edges of SCLK. The Si4736/37/38/39 acknowledges
each data byte by driving SDIO low for one cycle, on the
next falling edge of SCLK. The user may write up to 8
data bytes in a single 2-wire transaction. The first byte is
a command, and the next seven bytes are arguments.
24
Rev. 1.0
相关PDF资料 |
PDF描述 |
|---|---|
| IXTP90N075T2 | MOSFET N-CH 75V 90A TO-220 |
| SI4738-C40-GMR | IC RX FM/WB RADIO 20UQFN |
| SI4738-C40-GUR | IC RX FM/WB RADIO 24SSOP |
| SI4330-B1-FMR | IC RX ISM 240-960MHZ 20VQFN |
| SI4322-A0-FTR | IC RX FSK UNI 868/915MHZ 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI4740 | 制造商:SILABS 制造商全称:SILABS 功能描述:Automotive AM/FM Radio Receiver |
| SI4740-C10-GM | 功能描述:IC TUNER AM/FM CAR RADIO 24QFN RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| SI4740-C10-GMR | 制造商:Silicon Laboratories Inc 功能描述:SI4740-C10-GM AM/FM AUTOMOTIVE RADIO RX - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC TUNER AM/FM CAR RADIO 24QFN |
| SI4741 | 制造商:SILABS 制造商全称:SILABS 功能描述:Automotive AM/FM Radio Receiver |
| SI4741-B-EVB | 制造商:Silicon Laboratories Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。