- 您现在的位置：买卖IC网 > PDF目录9580 > SI5315B-C-GM (Silicon Laboratories Inc)IC CLOCK MULT 8KHZ-125MHZ 36QFN PDF资料下载
参数资料
| 型号： | SI5315B-C-GM |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 26/54页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK MULT 8KHZ-125MHZ 36QFN |
| 应用说明： | SI5315/17 Crystal Selection AppNote |
| 标准包装： | 490 |
| 系列： | DSPLL® |
| 类型： | 时钟/频率倍增器，抖动衰减器，多路复用器 |
| PLL： | 无 |
| 主要目的： | 以太网，SONET/SDH/PDH，电信 |
| 输入： | CML，CMOS，LVDS，LVPECL |
| 输出： | CML，CMOS，LVDS，LVPECL |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:2 |
| 差分 - 输入:输出： | 是/是 |
| 频率 - 最大： | 125MHz |
| 电源电压： | 1.71 V ~ 3.63 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-VFQFN 裸露焊盘 |
| 供应商设备封装： | 36-QFN（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
Si5315
32
Rev. 1.0
5.5. Holdover Mode
If an LOS condition exists on the selected input clock, the device enters holdover. In this mode, the device provides
a stable output frequency until the input clock returns and is validated. When the device enters holdover, the
internal oscillator is initially held to its last frequency value. Next, the internal oscillator slowly transitions to a
historical average frequency value that was taken over a time window of 6,711 ms in size that ended 26 ms before
the device entered holdover. This frequency value is taken from an internal memory location that keeps a record of
previous DSPLL frequency values. By using a historical average frequency, input clock phase and frequency
transients that may occur immediately preceding loss of clock or any event causing holdover do not affect the
holdover frequency. Also, noise related to input clock jitter or internal PLL jitter is minimized.
If a highly stable reference, such as an oven-controlled crystal oscillator, is supplied at XA/XB, an extremely stable
holdover can be achieved. If a crystal is supplied at the XA/XB port, the holdover stability will be limited by the
stability of the crystal; Table 3, “AC Characteristics” gives the specifications related to the holdover function.
5.5.1. Recovery from Holdover
When the input clock signal returns, the device transitions from holdover to the selected input clock. The device
performs hitless recovery from holdover. The clock transition from holdover to the returned input clock includes
"phase buildout" to absorb the phase difference between the holdover clock phase and the input clock phase. See
Table 3, “AC Characteristics” for specifications.
5.6. PLL Bypass Mode
The Si5315 supports a PLL bypass mode in which the selected input clock is fed directly to both enabled output
buffers, bypassing the DSPLL. Internally, the bypass path is implemented with high-speed differential signaling;
however, this path is not a low jitter path and will see significantly higher jitter on CKOUT. In PLL bypass mode, the
input and output clocks will be at the same frequency. PLL bypass mode is useful in a laboratory environment to
measure system performance with and without the jitter attenuation provided by the DSPLL. The DSBL2_BY pin is
used to select the PLL Bypass Mode according to Table 16. Bypass mode is not supported for CMOS clock outputs
(SFOUT = LH).
Table 15. Lock Detect Retrigger Time
PLL Bandwidth Setting (BW)
Retrigger Time (ms)
60–120 Hz
53
120–240 Hz
26.5
240–480 Hz
13.3
480–960 Hz
6.6
960–1920 Hz
3.3
1920–3840 Hz
1.66
3840–7680 Hz
0.833
Table 16. DSBL2/BYPASS Pin Settings
DSBL2/BYPASS
Function
L
CKOUT2 Enabled
M
CKOUT2 Disabled
H
PLL Bypass Mode w/ CKOUT2 Enabled
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33897AEF | IC TXRX CAN SGL WIRE 14-SOIC |
| VE-26X-MX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
| VI-B1K-MW-F2 | CONVERTER MOD DC/DC 40V 100W |
| VE-26W-MX-F1 | CONVERTER MOD DC/DC 5.5V 75W |
| MCZ33897BEFR2 | IC TXRX CAN SGL WIRE 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI5315B-C-GMR | 功能描述:时钟发生器及支持产品 Pin-Ctrl SyncE Clk Xplier/Jitt Attn 2/2 RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| SI5315-C | 制造商:AUK 制造商全称:AUK corp 功能描述:IRED |
| SI5315-C(B) | 制造商:AUK 制造商全称:AUK corp 功能描述:IRED |
| SI5315-C_1 | 制造商:AUK 制造商全称:AUK corp 功能描述:IRED |
| SI5315-CB | 制造商:AUK 制造商全称:AUK corp 功能描述:IRED |
发布紧急采购，3分钟左右您将得到回复。