- 您现在的位置：买卖IC网 > PDF目录1243 > SI5XX-PROG-EVB (Silicon Laboratories Inc)KIT EVALUATION FOR SI5XX PDF资料下载
参数资料
| 型号： | SI5XX-PROG-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 14/32页 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION FOR SI5XX |
| 标准包装： | 1 |
| 主要目的： | 计时，可重新配置的振荡器 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | Si514，Si570，Si571，Si598，Si599 |
| 主要属性： | 100kHz ~ 1.4GHz 频率范围 |
| 次要属性： | I²C 接口 |
| 已供物品： | 板，线缆，文档，软件 |
| 其它名称： | 336-2011 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Si570/Si571
RFREQ new = RFREQ current ? -------------------------
f out = ----------------------------------------- = -------------------------------------------
3. Functional Description
The Si570 XO and the Si571 VCXO are low-jitter
oscillators ideally suited for applications requiring
programmable frequencies. The Si57x can be
programmed to generate virtually any output clock in
the range of 10 MHz to 1.4 GHz. Output jitter
performance complies with and exceeds the strict
requirements of high-speed communication systems
including OC-192/STM-64 and 10 Gigabit Ethernet
(10 GbE).
The Si57x consists of a digitally-controlled oscillator
(DCO) based on Silicon Laboratories' third-generation
DSPLL technology, which is driven by an internal fixed-
frequency crystal reference.
The device's default output frequency is set at the
factory and can be reprogrammed through the two-wire
I 2 C serial port. Once the device is powered down, it will
return to its factory-set default output frequency.
While the Si570 outputs a fixed frequency, the Si571
has a pullable output frequency using the voltage
control input pin. This makes the Si571 an ideal choice
for high-performance, low-jitter, phase-locked loops.
3.1. Programming a New Output
Frequency
The output frequency (f out ) is determined by
programming the DCO frequency (f DCO ) and the
device's output dividers (HS_DIV, N1). The output
frequency is calculated using the following equation:
f DCO f XTAL ? RFREQ
Output Dividers HSDIV ? N1
The DCO frequency is adjustable in the range of 4.85 to
5.67 GHz by setting the high-resolution 38-bit fractional
multiplier (RFREQ). The DCO frequency is the product
of the internal fixed-frequency crystal (f XTAL ) and
RFREQ.
The 38-bit resolution of RFREQ allows the DCO
frequency to have a programmable frequency resolution
of 0.09 ppb.
Center
Frequency
Configuration
As shown in Figure 3, the device allows reprogramming
of the DCO frequency up to ±3500 ppm from the center
frequency configuration without interruption to the
output clock. Changes greater than the ±3500 ppm
window will cause the device to recalibrate its internal
tuning circuitry, forcing the output clock to momentarily
stop and start at any arbitrary point during a clock cycle.
This re-calibration process establishes a new center
frequency and can take up to 10 ms. Circuitry receiving
a clock from the Si57x device that is sensitive to glitches
or runt pulses may have to be reset once the
recalibration process is complete.
3.1.1. Reconfiguring the Output Clock for a Small
Change in Frequency
For output changes less than ±3500 ppm from the
center frequency configuration, the DCO frequency is
the only value that needs reprogramming. Since
f DCO = f XTAL x RFREQ, and that f XTAL is fixed, changing
the DCO frequency is as simple as reconfiguring the
RFREQ value as outlined below:
1. Using the serial port, read the current RFREQ value
(addresses 7–12 for all Si571 devices and Si570
devices with 20 ppm and 50 ppm temperature
stability; or addresses 13–18 for Si570 devices with
7 ppm temperature stability).
2. Calculate the new value of RFREQ given the change
in frequency.
f out_new
f out_current
3. Using the serial port, write the new RFREQ value
(addresses 7–12 for all Si571 devices and Si570
devices with 20 ppm and 50 ppm temperature
stability; or addresses 13–18 for Si570 devices with
7 ppm temperature stability).
Example:
An Si570 generating a 148.35 MHz clock must be
reconfigured "on-the-fly" to generate a 148.5 MHz clock.
This represents a change of +1011.122 ppm, which is
well within the ±3500 ppm window.
small frequency changes can be made
“on-the-fly” without interruption to the
output clock
4.85 GHz
-3500 ppm
+3500 ppm
5.67 GHz
Figure 3. DCO Frequency Range
14
Rev. 1.4
相关PDF资料 |
PDF描述 |
|---|---|
| SI84XXCOM-RD | KIT EVAL FOR SI84XXCOM |
| SILICON-EXPLORER II | SOFTWARE ANALYSIS EXPLORER LOGIC |
| SILINKPS-EVB | DAUGHTER CARD PROSLIC PS |
| SKP16C26A | DEV EVALUATION KIT M16C/26A |
| SKP32C85-100-CL | DEV EVALUATION KIT M32C/85 100PN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI5XXUC-EVB | 功能描述:XO & VCXO UNIVERSAL EVAL BOARD 制造商:silicon labs 系列:- 零件状态:在售 主要用途:计时，时钟振荡器 嵌入式:- 使用的 IC/零件:Si5xxUC 主要属性:- 辅助属性:- 所含物品:板 标准包装:1 |
| SI-60001 | 制造商:Bel Fuse 功能描述:CONN RJ-45 RCP 8 POS 2.54MM SLDR RA TH 12TERM - Trays |
| SI-60001-F | 功能描述:CONN MAGJACK 1PORT SHLD 10/100BT RoHS:是 类别:连接器，互连式 >> 模块 - 带磁性元件的插座 系列:MagJack® ST SI-60000 标准包装:60 系列:ARJ11D 连接器类型:RJ45 端口数:1 行数:1 安装类型:通孔，直角 速度:10/100 Base-T 板上方高度:0.545"（13.84mm） LED 颜色:绿 - 黄 每一插座芯体的数目:4 屏蔽:屏蔽式，EMI指 翼片方向:上 特点:AutoMDIX，板锁 包装:托盘 |
| SI-60002 | 制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:SI-60002 |
| SI-60002-F | 功能描述:CONN MAGJACK 1PORT SHLD 10/100BT RoHS:是 类别:连接器，互连式 >> 模块 - 带磁性元件的插座 系列:MagJack® ST SI-60000 标准包装:60 系列:ARJ11D 连接器类型:RJ45 端口数:1 行数:1 安装类型:通孔，直角 速度:10/100 Base-T 板上方高度:0.545"（13.84mm） LED 颜色:绿 - 黄 每一插座芯体的数目:4 屏蔽:屏蔽式，EMI指 翼片方向:上 特点:AutoMDIX，板锁 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。