- 您现在的位置：买卖IC网 > PDF目录21363 > SI8442AA-D-IS1 (Silicon Laboratories Inc)IC ISOLATOR 4CH 5.5V 16-SOIC PDF资料下载
参数资料
| 型号： | SI8442AA-D-IS1 |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 22/38页 |
| 文件大小： | 0K |
| 描述： | IC ISOLATOR 4CH 5.5V 16-SOIC |
| 视频文件： | Digital Isolation Overview Digital Isolators vs. Optocouplers |
| 标准包装： | 48 |
| 系列： | ISOpro |
| 输入 - 1 侧/2 侧： | 2/2 |
| 通道数： | 4 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电压 - 隔离： | 1000Vrms |
| 数据速率： | 1Mbps |
| 传输延迟： | 35ns |
| 输出类型： | 三态 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
| 配用： | 336-1765-ND - KIT EVAL FOR SI84XXISO |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
Si8440/41/42/45
2.4. Layout Recommendations
To ensure safety in the end user application, high voltage circuits (i.e., circuits with >30 V AC ) must be physically
separated from the safety extra-low voltage circuits (SELV is a circuit with <30 V AC ) by a certain distance
(creepage/clearance). If a component, such as a digital isolator, straddles this isolation barrier, it must meet those
creepage/clearance requirements and also provide a sufficiently large high-voltage breakdown protection rating
(commonly referred to as working voltage protection). Table 6 on page 15 and Table 7 on page 15 detail the
working voltage and creepage/clearance capabilities of the Si84xx. These tables also detail the component
standards (UL1577, IEC60747, CSA 5A), which are readily accepted by certification bodies to provide proof for
end-system specifications requirements. Refer to the end-system specification (61010-1, 60950-1, etc.)
requirements before starting any design that uses a digital isolator.
The following sections detail the recommended bypass and decoupling components necessary to ensure robust
overall performance and reliability for systems using the Si84xx digital isolators.
2.4.1. Supply Bypass
Digital integrated circuit components typically require 0.1 μF (100 nF) bypass capacitors when used in electrically
quiet environments. However, digital isolators are commonly used in hazardous environments with excessively
noisy power supplies. To counteract these harsh conditions, it is recommended that an additional 1 μF bypass
capacitor be added between VDD and GND on both sides of the package. The capacitors should be placed as
close as possible to the package to minimize stray inductance. If the system is excessively noisy, it is
recommended that the designer add 50 to 100 ? resistors in series with the VDD supply voltage source and 50 to
300 ? resistors in series with the digital inputs/outputs (see Figure 8). For more details, see "3. Errata and Design
Migration Guidelines" on page 25.
All components upstream or downstream of the isolator should be properly decoupled as well. If these components
are not properly decoupled, their supply noise can couple to the isolator inputs and outputs, potentially causing
damage if spikes exceed the maximum ratings of the isolator (6 V). In this case, the 50 to 300 ? resistors protect
the isolator's inputs/outputs (note that permanent device damage may occur if the absolute maximum ratings are
exceeded). Functional operation should be restricted to the conditions specified in Table 1, “Recommended
Operating Conditions,” on page 4.
2.4.2. Pin Connections
No connect pins are not internally connected. They can be left floating, tied to V DD , or tied to GND.
2.4.3. Output Pin Termination
The nominal output impedance of an isolator driver channel is approximately 85 ? , ±40%, which is a combination
of the value of the on-chip series termination resistor and channel resistance of the output driver FET. When driving
loads where transmission line effects will be a factor, output pins should be appropriately terminated with controlled
impedance PCB traces. The series termination resistor values should be scaled appropriately while keeping in
mind the recommendations described in “2.4.1. Supply Bypass” above.
V Source 1
R1 (50 – 100 ? )
VDD1
VDD2
V Source 2
R2 (50 – 100 ? )
C1
0.1 ? F
C2
50 – 300 ?
A1
B1
50 – 300 ?
C3
C4
0.1 ? F
1 ? F
Input/Output
50 – 300 ?
Ax
GND1
Bx
GND2
Input/Output
50 – 300 ?
1 ? F
Figure 8. Recommended Bypass Components for the Si84xx Digital Isolator Family
22
Rev. 1.6
相关PDF资料 |
PDF描述 |
|---|---|
| 3-641313-8 | CONN RCPT 8POS 26AWG .100 BLUE |
| 3-641311-8 | CONN RCPT 8POS 22AWG .100 RED |
| SI8441AA-D-IS1 | IC ISOLATOR 4CH 5.5V 16-SOIC |
| 3-640471-8 | CONN RCPT 8POS 28AWG .100 GREEN |
| 70M-OAC15 | OUTPUT MODULE AC MINI 9MA 15VDC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI8442AA-D-IS1R | 功能描述:隔离器接口集成电路 QuadCh 1.0kV Isolatr 1M 2/2 RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| Si8442AB-C-IS | 功能描述:隔离器接口集成电路 Quad Ch 2.5kV Isolator 1M 2/2 RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| SI8442AB-C-IS1 | 功能描述:隔离器接口集成电路 QuadCh 2.5kV Isolatr 1M 2/2 RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| Si8442AB-C-IS1R | 功能描述:隔离器接口集成电路 QuadCh 2.5kV Isolatr 1M 2/2 RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| Si8442AB-C-ISR | 功能描述:隔离器接口集成电路 QuadCh 2.5kV Isolatr 1M 2/2 RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。