参数资料
| 型号： | SI9102DN02-E3 |
| 厂商： | Vishay Siliconix |
| 文件页数： | 6/10页 |
| 文件大小： | 0K |
| 描述： | IC REG MULTI CONFIG 4V 20PLCC |
| 标准包装： | 500 |
| 类型： | 回扫，正向转换器，隔离式 |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 4V |
| 输入电压： | 10 V ~ 120 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 40kHz ~ 1MHz |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-LCC（J 形引线） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 20-PLCC（9x9） |
Si9102
Vishay Siliconix
DETAIL DESCRIPTION
Product is End of Life 3/2014
BIAS
To properly set the bias for the Si9102, a 390 k Ω resistor
should be tied from BIAS to - V IN . This determines the mag-
nitude of bias current in all of the analog sections and the
pull-up current for the SHUTDOWN and RESET pins. The
current flowing in the bias resistor is nominally 15 μA.
Reference Section
The reference section of the Si9102 consists of a tempera-
ture compensated buried zener and trimmable divider net-
work. The output of the reference section is connected
internally to the non-inverting input of the error amplifier.
Nominal reference output voltage is 4 V. The trimming proce-
dure that is used on the Si9102 brings the output of the error
amplifier (which is configured for unity gain during trimming)
to within ± 1 % of 4 V. This automatically compensates for the
input offset voltage in the error amplifier.
SHUTDOWN and RESET
SHUTDOWN and RESET are intended for overriding the
output MOSFET switch via external control logic. The two
inputs are fed through a latch preceding the output switch.
Depending on the logic state of RESET, SHUTDOWN can
be either a latched or unlatched input. The output is off when-
ever SHUTDOWN is low. By simultaneously having SHUT-
DOWN and RESET low, the latch is set and SHUTDOWN
has no effect until RESET goes high. The truth table for these
inputs is given in Table 1.
Both pins have internal current source pull-ups and should
be left disconnected when not in use. An added feature of the
current sources is the ability to connect a capacitor and an
open-collector driver to the SHUTDOWN or RESET pins to
provide variable shutdown time.
Table 1. Truth Table for the SHUTDOWN and RESET Pins
The output impedance of the reference section has been
purposely made high so that a low impedance external volt-
age source can be used to override the internal voltage
source, if desired, without otherwise altering the perfor-
mance of the device.
SHUTDOWN
H
H
L
L
RESET
H
H
L
L
Output
Normal Operation
Normal Operation (No Change)
Off (Not Latched)
Off (Latched)
Off (Latched, No Change)
Error Amplifier
Closed-loop regulation is provided by the error amplifier,
which is intended for use with "around-the-amplifier" com-
pensation. A MOS differential input stage provides for low
input current. The noninverting input to the error amplifier
(V REF ) is internally connected to the output of the reference
supply and should be bypassed with a small capacitor to
ground.
Oscillator Section
The oscillator consists of a ring of CMOS inverters, capaci-
tors, and a capacitor discharge switch. Frequency is set by
an external resistor between the OSC in and OSC out pins.
(See Figure 5 for details of resistor value vs. frequency.) The
DISCHARGE pin should be tied to - V IN for normal internal
oscillator operation. A frequency divider in the logic section
limits switch duty cycle to ≤ 50 % by locking the switching fre-
quency to one half of the oscillator frequency.
Remote synchronization can be accomplished by capacitive
coupling of a synchronization pulse into the OSC IN terminal.
For a 5 V pulse amplitude and 0.5 μs pulse width, typical val-
ues would be 100 pF in series with 3 k Ω to OSC IN.
www.vishay.com
6
Output Switch
The output switch is a 7 Ω , 200 V lateral DMOS device. Like
discrete MOSFETs, the switch contains an intrinsic body-
drain diode. However, the body contact in the Si9102 is con-
nected internally to - V IN and is independent of the SOURCE.
Document Number: 70001
S-70497-Rev. H, 19-Mar-07
相关PDF资料 |
PDF描述 |
|---|---|
| SI9104DW-E3 | IC REG MULTI CONFIG 4V 16SOIC |
| SI9105DN02-E3 | IC REG FLYBK ISOLATED 4V 20PLCC |
| SI9108DN02-E3 | IC REG FLYBK ISOLATED 4V 20PLCC |
| SI9110DY-T1-E3 | IC REG CTRLR FLYBK CUK CM 14SOIC |
| SI9112DY-E3 | IC REG CTRLR FLYBK CUK CM 14SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI9102DN02-T1 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:3-W High-Voltage Switchmode Regulator |
| SI9102DN02-T1-E3 | 功能描述:开关变换器、稳压器与控制器 3W High-Voltage Switchmode RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| SI9102N02-E3 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:3-W High-Voltage Switchmode Regulator |
| SI9104 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:High-Voltage Switchmode Regulator |
| SI9104DW | 功能描述:直流/直流开关转换器 3W HV Switchmode Reg RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。