- 您现在的位置：买卖IC网 > PDF目录368620 > SI9112DY (Vishay Intertechnology,Inc.) High-Voltage Switchmode Controller PDF资料下载
参数资料
| 型号： | SI9112DY |
| 厂商： | Vishay Intertechnology,Inc. |
| 英文描述： | High-Voltage Switchmode Controller |
| 中文描述： | 高电压开关模式控制器 |
| 文件页数： | 5/6页 |
| 文件大小： | 71K |
| 代理商： | SI9112DY |
BIAS
FB
+V
IN
COMP
SENSE
RESET
OUTPUT
SHUTDOWN
V
IN
V
REF
V
CC
DISCHARGE
OSC OUT
OSC IN
Dual-In-Line and SOIC
1
2
3
4
5
6
7
14
13
12
11
10
9
8
Top View
Si9112
Vishay Siliconix
sDocument Number: 70005
S-42036—Rev. H, 15-Nov-04
www.vishay.com
5
PIN CONFIGURATIONS AND ORDERING INFORMATION
ORDERING INFORMATION
Part Number
Temperature Range
Package
Si9112DY
Si9112DY-T1
Si9112DY-T1—E3
Si9112DJ
Si9112DJ—E3
SOIC-14
40 to 85 C
PDIP-14
DETAILED DESCRIPTION
Pre-Regulator/Start-Up Section
Due to the low quiescent current requirement of the Si9112
control circuitry, bias power can be supplied from the
unregulated input power source, from an external regulated
low-voltage supply, or from an auxiliary “bootstrap” winding on
the output inductor or transformer.
When power is first applied during start-up, +V
IN
(pin 2) will
draw a constant current. The magnitude of this current is
determined by a high-voltage depletion MOSFET device
which is connected between +V
IN
and V
CC
(pin 6). This
start-up circuitry provides initial power to the IC by charging an
external bypass capacitance connected to the V
CC
pin. The
charging current is disabled when V
CC
exceeds 8.7 V. If V
CC
is
not forced to exceed the 8.7-V threshold, then V
CC
will be
regulated to a nominal value of 8.7 V by the pre-regulator
circuit.
As the supply voltage rises toward the normal operating
conditions, an internal undervoltage (UV) lockout circuit keeps
the output driver disabled until V
CC
exceeds the UV lockout
threshold (typically 8.1 V). This guarantees that the control
logic will be functioning properly and that sufficient gate drive
voltage is available before the MOSFET turns on. The design
of the IC is such that the undervoltage lockout threshold will be
at least 300 mV less than the pre-regulator turn-off voltage.
Power dissipation can be minimized by providing an external
power source to V
CC
such that the pre-regulator circuit is
disabled.
BIAS
To properly set the bias for the Si9112, a 270-k
should be tied from BIAS (pin 1) to
V
IN
(pin 5). This
resistor
determines the magnitude of bias current in all of the analog
sections and the pull-up current for the SHUTDOWN and
RESET pins. The current flowing in the bias resistor is
nominally 15 A.
Reference Section
The reference section of the Si9112 consists of a temperature
compensated buried zener and trimmable divider network.
The output of the reference section is connected internally to
the non-inverting input of the error amplifier. Nominal reference
output voltage is 4 V. The trimming procedure that is used on
the Si9112 brings the output of the error amplifier (which is
configured for unity gain during trimming) to within
This automatically compensates for input offset voltage in the
error amplifier.
2% of 4 V.
The output impedance of the reference section has been
purposely made high so that a low impedance external voltage
source can be used to override the internal voltage source, if
desired, without otherwise altering the performance of the
device.
Error Amplifier
Closed-loop regulation is provided by the error amplifier. The
emitter follower output has a typical dynamic output
impedance of 1000
“around-the-amplifier” compensation. A MOS differential input
stage provides low input leakage current. The noninverting
input to the error amplifier (V
REF
) is internally connected to the
output of the reference supply and should be bypassed with a
small capacitor to ground.
, and is intended for use with
相关PDF资料 |
PDF描述 |
|---|---|
| SI9112DY-T1 | High-Voltage Switchmode Controller |
| SI9112DY-T1-E3 | High-Voltage Switchmode Controller |
| SI9114A | High-Frequency Switchmode Controller |
| Si9114ADJ | High-Frequency Switchmode Controller |
| Si9114ADJ-E3 | High-Frequency Switchmode Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI9112DY-E3 | 功能描述:开关变换器、稳压器与控制器 Hi-Eff/Hi-Voltage Switchmode RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| SI9112DY-T1 | 功能描述:开关变换器、稳压器与控制器 Hi-Eff/Hi-Voltage Switchmode RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| SI9112DY-T1-E3 | 功能描述:开关变换器、稳压器与控制器 Hi-Eff/Hi-Voltage Switchmode RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| SI9113 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:High-Voltage Current Mode PWM Controller for ISDN Power Supplies |
| SI9113_04 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:High-Voltage Current Mode PWM Controller for ISDN Power Supplies |
发布紧急采购，3分钟左右您将得到回复。