参数资料
| 型号： | SL16020DC |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 8/10页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK AMD GRAPHICS 10TDFN |
| 标准包装： | 490 |
| 系列： | EProClock® |
| 类型： | * |
| PLL： | 带旁路 |
| 输入： | 时钟，晶体 |
| 输出： | 时钟 |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:2 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 100MHz |
| 除法器/乘法器： | 无/无 |
| 电源电压： | 2.97 V ~ 3.63 V |
| 工作温度： | -10°C ~ 85°C |
| 安装类型： | * |
| 封装/外壳： | * |
| 供应商设备封装： | * |
| 包装： | * |
Rev 2.2, August 1, 2010
Page 7 of 10
SL16020DC
External Components and Design Considerations
Typical Application Circuit
SL16020DC
XIN(1)
VDD2(8)
XOUT(10)
SSCLK(5)
SSEL1(3)
SSEL0(7)
100MHz
27MHz
CL1
CL2
0.1
μF
VSS2(2)
REFCLK(9)
27MHz
VSS1(6)
VDD1(4)
10
μF
External crystal and crystal
load capacitors required if
crystal is used.
If external clock (XO) is used
leave Pin-10 XOUT
unconnected (N/C) and drive
Pin 1 XIN/CLKIN with clock
VDD
0.1
μF
5K
This example is configured
for -0.5% Spread
SSEL0=M (VDD/2) and
SSEL1=LOW (VSS)
5K
Figure 4. Typical Application Schematic
Comments and Recommendations
Crystal and Crystal Load: Only use a parallel resonant fundamental AT cut crystal. DO NOT USE higher overtone
crystals. To meet the crystal initial accuracy specification (in ppm) make sure that external crystal load capacitor is
matched to crystal load specification. To determine the value of CL1 and CL2, use the following formula;
C1 = C2 = 2CL – (Cpin + Cp)
Where: CL is load capacitance stated by crystal manufacturer
Cpin is the SL16010 pin capacitance (4pF)
Cp is the parasitic capacitance of the PCB traces.
EXAMPLE; if a crystal with CL=12pF specification is used and Cp=1pF (parasitic PCB capacitance on PCB), 19 or
20pF external capacitors from pins XIN (pin-1) and XOUT (Pin-10) to VSS are required since CXIN=CXOUT=4pF for
the SL1610DC product. Users must verify Cp value.
Decoupling Capacitor: A decoupling ca
pacitor of 0.1μF must be used between VDD1/2 pins and VSS1/2 pin. Place
the capacitor on the component side of the PCB as close to the VDD1/2 pins as possible. The PCB trace to the
VDD1/2 pins and to the VSS via should be kept as short as possible Do not use vias between the decoupling
capacitor and the VDD1/2 pins. In addition, a 10uf capacitor should be placed between VDD and VSS.
Series Termination Resistor: A series termination resistor is recommended if the distance between the outputs
(REFCLK and SSCLK) and the load if PCB trace is over 1 inch. The nominal impedance of the outputs is about 24
Ω. Use 22 Ω resistors in series with the outputs to terminate 50Ω trace impedance and place 22 Ω resistors as close
相关PDF资料 |
PDF描述 |
|---|---|
| X9421WV14IZT1 | IC XDCP SGL 64-TAP 10K 14-TSSOP |
| X9421WV14IZ-2.7 | IC XDCP SGL 64-TAP 10K 14-TSSOP |
| X9421WV14IZ | IC XDCP SGL 64-TAP 10K 14-TSSOP |
| MS3456L24-7P | CONN PLUG 16POS STRAIGHT W/PINS |
| V28A6V5H200BG3 | CONVERTER MOD DC/DC 6.5V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SL16020DCT | 功能描述:时钟发生器及支持产品 AMD Graphics clock RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| SL160810NJL | 制造商:ABC 制造商全称:ABC Taiwan Electronics Corp 功能描述:WOUND CHIP INDUCTOR |
| SL160812NJL | 制造商:ABC 制造商全称:ABC Taiwan Electronics Corp 功能描述:WOUND CHIP INDUCTOR |
| SL160815NJL | 制造商:ABC 制造商全称:ABC Taiwan Electronics Corp 功能描述:WOUND CHIP INDUCTOR |
| SL160818NJL | 制造商:ABC 制造商全称:ABC Taiwan Electronics Corp 功能描述:WOUND CHIP INDUCTOR |
发布紧急采购，3分钟左右您将得到回复。