- 您现在的位置：买卖IC网 > PDF目录299901 > SLIN-03E1AL (BEL FUSE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | SLIN-03E1AL |
| 厂商： | BEL FUSE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, PACKAGE-10 |
| 文件页数： | 10/26页 |
| 文件大小： | 456K |
| 代理商： | SLIN-03E1AL |
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302
Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
18
NON-ISOLATED DC/DC CONVERTERS
4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs
October 8, 2009
Bel Power, Inc. , a subsidiary of Bel Fuse, Inc.
Output Voltage Sequencing (continued)
After applying input voltage to the module, a minimum 10msec delay is required before applying voltage on the
SEQ pin. During this time, a voltage of 50mV (± 20 mV) is maintained on the SEQ pin. This delay gives the
module enough time to complete its internal power-up soft-start cycle. During the delay time, the SEQ pin
should be held close to ground (nominally 50mV ± 20 mV). This is required to keep the internal op-amp out of
saturation thus preventing output overshoot during the start of the sequencing ramp. By selecting resistor R1
according to the following equation:
05
.
0
24950
1
=
IN
V
R
The voltage at the sequencing pin will be 50mV when the sequencing signal is at zero.
R1
GND
VIN+
SEQ
+
-
OUT
10K
499K
MODULE
Circuit showing connection of the sequencing signal to the SEQ pin
After the 10msec delay, an analog voltage is applied to the SEQ pin and the output voltage of the module will
track this voltage on a one-to-one volt bases until the output reaches the set-point voltage.
To initiate
simultaneous shutdown of the modules, the SEQ pin voltage is lowered in a controlled manner. The output
voltage of the modules tracks the voltages below their set-point voltages on a one-to-one basis. A valid input
voltage must be maintained until the tracking and output voltages reach ground potential.
When using the sequencing feature to control start-up of the module, pre-bias immunity during start-up is
disabled. The pre-bias immunity feature of the module relies on the module being in the diode-mode during
start-up. When using the sequencing feature, modules goes through an internal set-up time of 10msec, and will
be in synchronous rectification mode when the voltage at the SEQ pin is applied. This will result in the module
sinking current if a pre-bias voltage is present at the output of the module. When pre-bias immunity during start-
up is required, the sequencing feature must be disabled.
For additional guidelines on using the sequencing
feature please contact the Bel Power technical representative for additional information.
ohms
相关PDF资料 |
PDF描述 |
|---|---|
| SLL-50HF1B | LOGIC OUTPUT PHOTO DETECTOR |
| SLS121PC | SLIDE SWITCH, SPDT, LATCHED, 0.15A, 12VDC, THROUGH HOLE-STRAIGHT |
| SLS121RA | SLIDE SWITCH, SPDT, LATCHED, 0.15A, 12VDC, THROUGH HOLE-RIGHT ANGLE |
| SLS151RA | SLIDE SWITCH, SP5T, LATCHED, 0.15A, 12VDC, THROUGH HOLE-RIGHT ANGLE |
| SLVDA2.8 | 300 W, BIDIRECTIONAL, 4 ELEMENT, SILICON, TVS DIODE, MS-012AA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SLIN-03E1ALG | 制造商:Bel Fuse 功能描述:DC/DC CONVERTR NON-ISO 0.59-5.5V |
| SLIN-03E1AX | 制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.59 Vdc - 5.5 Vdc /3 A Outputs |
| SLIN-03E2A | 制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:NON-ISOLATED DC/DC CONVERTERS |
| SLIN-03E2A_10 | 制造商:BEL 制造商全称:Bel Fuse Inc. 功能描述:NON-ISOLATED DC/DC CONVERTERS |
| SLIN-03E2A0 | 功能描述:DC/DC CONVERTR NON-ISO 0.6-3.63V RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:* 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:21V 电压 - 输入（最大）:32V Voltage - Output 1:24V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 1.05" H（116.8mm x 47.2mm x 26.7mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
发布紧急采购，3分钟左右您将得到回复。