- 您现在的位置：买卖IC网 > Datasheet目录517 > SM1230E868 (Semtech)BOARD EVAL XMITTER FOR SX1230 Datasheet资料下载
参数资料
| 型号： | SM1230E868 |
| 厂商： | Semtech |
| 文件页数： | 18/46页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL XMITTER FOR SX1230 |
| 设计资源： | SM1230 BOM SX1230 Eval Board Schematic |
| 标准包装： | 1 |
| 类型： | 发射器 |
| 频率： | 868MHz |
| 适用于相关产品： | SX1230 |
| 已供物品： | 板 |
| 产品目录页面： | 584 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
SX1230
Integrated Transmitter IC
ADVANCED COMMUNICATIONS & SENSING
DATASHEET
where T RC is the RC oscillator period, periodic_n is programmable between 0 and 15 and periodic_d may take values
between 0 and 10. The maximum period is hence approximately 125 s when the frequency of the RC oscillator is 67 kHz.
Push button mode is enabled when the value of D is non-zero and, when activated, all stand alone mode functionality is
available. It is important to note that if there is no push button pressed, then no message will be transmitted.
6.1.4. Low Battery Indicator: Stand Alone Mode
The low battery indicator may be used in stand alone mode to detect the battery voltage and send a low battery message
to the receiver. It is enabled by setting the eol_frame_mode bit ‘high’ (register 0x12). The low battery state is determined by
comparing the supply voltage with a 1.695 V to 2.185 V programmable threshold (threshold trim_eol(2:0), address 0x12).
Following detection, the following actions are performed depending upon the exact mode of operation:
Normal Operation (Non-Periodic): The battery end-of-life condition is checked during the normal frame. If it is true, then
a single extra frame #14 (see Table 9) is automatically sent after the normal frame.
Stand-Alone Periodic Mode Operation: The battery end-of-life condition is checked during the normal frame. If it is true,
then the next frame, sent at the next timer tick is frame #14 (see Table 9), the frame is sent only once.
6.1.5. Low Battery Indicator: MCU Mode
In MCU mode the low battery status indicator may be accessed and configured via the SPI register EolCtrl. Alternatively,
the active high low battery indication is mapped to the PB0 pin allowing the independent generation of hardware interrupts.
6.2. MCU Mode
6.2.1. SPI Operation
The first byte in any data transfer over the SPI is the address read/write byte. It comprises:
1. W/RB bit, which is 1 for write access and 0 for read access
2. 7 bits of address, MSB first.
A transfer always starts by the NSS (not slave select) signal going low whilst SCK is high. MOSI (master out - slave in) is
generated by the master on the next falling edge of SCK and is sampled by the slave on the next rising edge of SCK. MISO
is generated by the slave on the falling edge of SCK and is high impedance when NSS is high. By convention, all bytes are
sent MSB first.
MCU mode is activated when pad E2_Mode is tied to GND (ground). In this mode the SX1230 is configured as SPI slave
and its internal configuration registers can be written following the format shown in Figure 7.
An ‘address write-byte‘ followed by a data byte is sent for a write access. Where multiple sequential registers are to be
written, the NSS input may be kept low after this first address-byte plus data-byte have been sent. In this state sequential
data-bytes may be written, the address is automatically incremented after the reception of each additional data-byte. This
allows the sequential data-bytes to be written without the need for an address byte. NSS must then be set ‘high’ after the
last byte transfer.
SX1230, Revision 2 May 2009
?2008 Semtech Corp.
Page 18
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SM16S-CM012-012 | SYNJET ZFLOW 50 PWM 12V |
| SM200P81 | RF MODULE 250/500MBPS 2.4GHZ SMA |
| SM2440G | LAMP T2 TELEPHONE SLIDE 24V .04A |
| SM3020G | LAMP T2 TELEPHONE SLIDE 30V .02A |
| SM3020S | LAMP T-1.5 TELE SLIDE 30V .02A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SM1230-XAX | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Power Optimizers Partial Deployment for Single String Systems |
| SM1230-XBX | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Power Optimizers Partial Deployment for Single String Systems |
| SM1231E433 | 制造商:Semtech Corporation 功能描述:Development Module for SX1231 433MHz Low Power Integrated UHF Transceiver 制造商:SEMTECH 功能描述:Development Module for SX1231 433MHz Low Power Integrated UHF Transceiver |
| SM1231E433A | 制造商:Semtech Corporation 功能描述:SX1231 RF MODULE 433 MHZ |
| SM1231E868 | 制造商:Semtech Corporation 功能描述:Development module for SX1231 868MHz Low Power Integrated UHF Transceiver 制造商:SEMTECH 功能描述:Development module for SX1231 868MHz Low Power Integrated UHF Transceiver |
发布紧急采购，3分钟左右您将得到回复。