- 您现在的位置：买卖IC网 > PDF目录16479 > SMARTPSE24-KIT (Silicon Laboratories Inc)KIT EVAL REF 24PORT SPI/UART PDF资料下载
参数资料
| 型号： | SMARTPSE24-KIT |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 6/36页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL REF 24PORT SPI/UART |
| 标准包装： | 1 |
| 主要目的： | 电源管理，以太网供电（POE），PSE |
| 已用 IC / 零件： | Si3452，Si3482，Si3500 |
| 已供物品： | 板，线缆，CD |
| 相关产品： | SI3482-A01-GM-ND - IC CTLR POE 24-48PORT PSE 24-QFN 336-1830-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1835-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1829-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1831-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1834-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1844-5-ND - IC POE SWITCH PWR OVER LAN 20QFN 336-1833-5-ND - IC POE CONTROLLER MIDSPAN 40QFN 336-1832-5-ND - IC POE CONTROLLER MIDSPAN 40QFN |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Si3452
14
Rev. 1.3
4.4. Disconnect Detection
The dV/dt disconnect function can be used to detect a disconnected device without using dc disconnect or ac
disconnect.
In dV/dt disconnect mode, the FET current limit is switched to 7.5 mA. If the voltage across the FET increases, a
load is assumed to be present, and the FET current limit is automatically switched back to its pre-selected value. If,
after 350 ms, the FET voltage has not increased, there is no load present, and the FET is turned off.
In addition to operating in a manner functionally distinct from DC disconnect, dV/dt disconnect requires no
additional external components and fully interoperates with all powered device DC Maintain Power Signatures. For
more information, see “AN399: dV/dt Disconnect and the IEEE 802.3 PoE Standard”.
4.5. Transient Voltage Surge Suppression
The Si3452 features robust on-chip surge protectors on each port; this is an industry first. This unique protection
circuitry acts as an active device that can withstand lightning-induced transients as well as large ESD transient
events. When the port voltage exceeds its protection limit and the current reaches a triggering threshold, current is
shunted from the port to the ground pins.
Internal circuitry is provided to protect the line outputs from externally-coupled fault currents. These are transient
currents of up to 5 A peak.
The operation of the protection circuits depends on the operating mode of the channel switch and the direction of
the fault current. The clamping operation is performed on the detect pin.
The switch itself will also be protected by the current limit. If the transient lasts long enough to heat up the die, then
the temperature sense circuit will shut off the switch, and all the fault current will flow through the clamp diode.
4.6. Temperature Sense
A temperature sense signal is used in conjunction with the current limit status signals from the gate drive blocks.
Any channel that is generating excess heat is assumed to be operating in current limit mode, with both high voltage
drop and high current.
If the port is in PoE mode, an overload will generally not result in thermal shutdown before the 60 ms ICUT period. If
the port is in PoE+ mode, an overload may cause the port to shut down prior to the 60 ms ICUT period. In either
case, the event is reported as ICUT. The faster shutdown in PoE+ mode is consistent with and specifically allowed
by the 802.3at draft and provides much more robust overload protection than is possible with external FETs.
In addition, there is a thermal shutdown if the package temperature exceeds 120 °C. If this threshold is reached, all
output drivers are turned off and detection modes are disabled. This secondary threshold limit guards against the
possibility that the overheating is not caused by a driver operating in current limit.
4.7. Port Measurement and Monitoring
VEE monitoring in conjunction with port current monitoring allows measurement of port power. Port power
monitoring, dynamic power allocation via LLDP*, and port power policing allow efficient power supply sizing.
The Si3452 is factory-calibrated and temperature-compensated for the following measurements:
Port current measurement. These measurements are auto-ranged and scaled to a 16 bit number at 100 A per
bit. Port current accuracy is ±4% ± 2 mA.
VEE is measured with a scale of 64 V. The measurement is reported as a 16-bit number scaled at 1 mV per bit.
VEE measurement accuracy is ±4% over the valid VEE range.
*Note:
LLDP = Link Layer Discovery Protocol. Refer to IEEE 802.3at (draft) and IEEE 802.1AB for more information.
相关PDF资料 |
PDF描述 |
|---|---|
| LBC2518T681M | INDUCTOR WOUND 680UH 45MA 1007 |
| VE-24D-EX | CONVERTER MOD DC/DC 85V 75W |
| 1SMA5926BT3 | DIODE ZENER 11V 1.5W SMA |
| ST16C2550CQ-0B-EB | EVAL BOARD FOR ST16C2551 48TQFP |
| 9-6278032-5 | C/A MT-RJ/MT-RJ MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SMARTRF06EBK | 功能描述:射频开发工具 SMARTRF06 EVAL BRD RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| SMARTRFTRXEBK | 功能描述:EVAL BOARD SMART RF 制造商:texas instruments 系列:- 零件状态:有效 类型:收发器 频率:- 配套使用产品/相关产品:MSP430 所含物品:板，线缆 标准包装:1 |
| SMARTSOCKET 575 TYPE D | 制造商:TIME MARK CORP SIGNALINE 功能描述:Nominal input voltage 575VAC, Max input voltage 635VAC |
| SMARTSTART-BAC-D | 制造商:IDEC Corporation 功能描述:PROGRAMMABLE LOGIC CONTROLLER, Accessory Type:Starter Kit, For Use With:FL1D Ser |
| SMARTSTART-BAC-E | 制造商:IDEC Corporation 功能描述:FL1E SMARTRELAY STARTER KIT 120-240VAC/DC BASE MODULE W/O LCD DISPLAY 制造商:IDEC Corporation 功能描述:STARTER KIT, AUTOMATION & PROCESS CONTRO 制造商:IDEC Corporation 功能描述:STARTER KIT, AUTOMATION & PROCESS CONTROL; No. of Inputs:12; No. of Outputs:12; Kit Contents:WindLGC 6.0 Software, FL1E-B12RCC and Serial Programming Cable; Supply Voltage Max:240VAC; Accessory Type:SmartRelay Starter Kit 制造商:IDEC Corporation 功能描述:FL1E-B12RCC, Windlgc Software And Programming Cable 制造商:IDEC CORPORATION 功能描述:FL1E SmartRelay Starter Kit |
发布紧急采购，3分钟左右您将得到回复。