- 您现在的位置：买卖IC网 > PDF目录10586 > SP202EET-L (Exar Corporation)IC DVR/RCVR RS232 QUAD 16WSOIC PDF资料下载
参数资料
| 型号： | SP202EET-L |
| 厂商： | Exar Corporation |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC DVR/RCVR RS232 QUAD 16WSOIC |
| 标准包装： | 41 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 2/2 |
| 规程： | RS232 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
| 其它名称： | 1016-1010-5 |
Exar Corporation 48720 Kato Road, Fremont CA, 94538 (50)668-7000 www.exar.com SP202E,232E,233E, 30E, 32E_0_0603
6
DESCRiPTion
C is charged from Vcc to prepare it for its next
phase.
Phase 3
Vdd charge store and double: Phase three is
identical to the first phase. The positive termi-
nals of C and C2 are charged from Vcc with
their negative terminals initially connected to
ground. C+ is then connected to ground and
the stored charge from C- is superimposed
onto C2-. Since C2+ is still connected to Vcc
the voltage potential across capacitor C2 is now
2 x Vcc.
Phase 4
Vdd transfer: The fourth phase connects the
negative terminal of C2 to ground and the posi-
tive terminal of C2 to the Vdd storage capacitor.
This transfers the doubled (V+) voltage onto C3.
Meanwhile, capacitor C is charged from Vcc to
prepare it for its next phase.
The clock rate for the charge pump typically op-
erates at greater than 5kHz allowing the pump
to run efficiently with small 0.1uF capacitors. Ef-
ficient operation depends on rapid charging and
discharging of C and C2, therefore capacitors
should be mounted as close as possible to the
IC and have low ESR (equivalent series resis-
tance). Inexpensive surface mount, ceramic ca-
pacitors are ideal for using on charge pump. If
polarized capacitors are used the positive and
negative terminals should be connected as
shown in the typical operating circuit. A diagram
of the individual phases are shown in Figure .
Shutdown (SD) and Enable (En) features for
the SP310E and SP312E
Both the SP30E and SP32E have a shutdown
/ standby mode to conserve power in battery-
powered applications. To activate the shutdown
mode, which stops the operation of the charge
pump, a logic "0" is applied to the appropriate
control line. For the SP30E, this control line is
the ON/OFF (pin 8) input. Activating the shut-
down mode puts the SP30E transmitter and
receiver ouptuts into a high impedance con-
dition. For the SP32E, this control line is the
SHUTDOWN (pin8) input; this also puts the
transmitter outputs in a tri-state mode. The re-
ceiver outputs can be tri-stated seperately dur-
ing normal operation or shutdown by applying a
logic "" on the EN line (pin ).
Wake-Up Feature for the SP312E
The SP32E has a wake-up feature that keeps
the receivers active when the device is placed
into shutdown. Table 1 defines the truth table for
the Wake-Up function. When only the receivers
are activated, the SP32E typically draws less
than 5uA supply current. In the case of when
a modem is interfaced to a computer in power
down mode, the Ring Indicator (RI) signal from
the modem would be used to "wake-up" the
computer, allowing it to accept data transmis-
sion.
After the ring indicator has propagated
through the SP32E receiver, it can be used
to trigger the power management circuitry of
the computer to power up the microproces-
sor, and bring the SD pin of the SP32E to a
logic high, taking it out of the shutdown mode.
The receiver propagation delay is typically
us. The enable time for V+ and V- is typi-
cally 2ms. After V+ and V- have settled to their
final values, a signal can be sent back to the
modem on the data terminal ready (DTR) pin
signifying that the computer is ready to accept
the transmit data.
SD EN
Power
Up/Down
Receiver
outputs
0
Down
Enabled
0
Down
Tri-state
0
Up
Enabled
Up
Tri-state
Table . Wake-up Function truth table
Pin Strapping for the SP233E
To operate properly, the following pairs of pins
must be externally wired together as noted in
table 2:
Pins Wired
Together
SOICW
Two V- pins
0 & 7
Two C2+ pins
2 & 5
Two C- pins
& 6
Connect Pins 6 and 9 to
GND
Table 2. Pin Strapping table for SP233E
相关PDF资料 |
PDF描述 |
|---|---|
| SP485EMN-L | IC TXRX RS485 HALF DUPLEX 8NSOIC |
| SP485EEP-L | IC TXRX RS485 HALF DUPLEX 8PDIP |
| TW8817-TA5-GRS | IC LCD CTRLR 80TQFP |
| SP232AET-L | IC DVR/RCVR RS232 LP 16WSOIC |
| TW8832SAT-LB1-GRSHT | IC TFT LCD CONTROLLER 80LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP202EET-L/TR | 功能描述:RS-232接口集成电路 HIGH PERFORMANCE RS232 -40-85C RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| SP202R00JLF | 功能描述:线绕电阻器 - 透孔 2 OHM 5% 1W RoHS:否 制造商:Bourns 电阻:10 Ohms 容差:5 % 功率额定值:7 W 温度系数:200 PPM / C 系列:FW 端接类型:Axial 工作温度范围:- 55 C to + 155 C 尺寸:9.5 mm Dia. x 26 mm L 封装:Ammo 产品:Power Resistors Wirewound High Energy |
| SP202R10JLF | 制造商:TT Electronics / IRC 功能描述:SP202R10JLF |
| SP202R20JLF | 制造商:TT Electronics / IRC 功能描述:SP202R20JLF |
| SP202R21KLF | 制造商:TT Electronics / IRC 功能描述:SP202R21KLF |
发布紧急采购，3分钟左右您将得到回复。