- 您现在的位置：买卖IC网 > PDF目录10157 > SP3075EMN-L (Exar Corporation)IC TXRX RS485/RS422 ESD 8NSOIC PDF资料下载
参数资料
| 型号： | SP3075EMN-L |
| 厂商： | Exar Corporation |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS485/RS422 ESD 8NSOIC |
| 标准包装： | 98 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS422/RS485 |
| 电源电压： | 3.3V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 管件 |
5
Exar Corporation 48720 Kato Road, Fremont CA, 94538 50-668-707 www.exar.com
SP3070E-SP3078E_02_2020
ESD structures withstand high ESD in all
states: normal operation, shutdown, and
powered down. After an ESD event, the
SP3070E - SP3078E keep working without
latchup or damage.
ESDprotectioncanbetestedinvariousways.
Thetransmitteroutputsandreceiverinputsof
the SP3070E - SP3078E are characterized
for protection to the following limits:
■ ±5kV using the Human Body Model
■ ±8kVusingtheContactDischargemethod
specified in IEC 61000-4-2
■ ±5kV Airgap
ESD TEST CONDITIONS
ESD performance depends on a variety
of conditions. Contact Exar for a reliability
report that documents test setup, methodol-
ogy and results.
IEC 61000-4-2
The IEC 6000-4-2 standard covers ESD
testing and performance of finished equip-
ment. However, it does not specifically refer
to integrated circuits. The SP3070E family
of devices helps you design equipment to
meet IEC 6000-4-2, without the need for
additional ESD-protection components.
The air-gap test involves approaching the
device with a charged probe. The contact-
discharge method connects the probe to the
device before the probe is energized.
MaCHINE MODEl
The machine model for ESD tests all pins
using a 200pF storage capacitor and zero
discharge resistance. The objective is to
emulate the stress caused when I/O pins
are contacted by handling equipment during
test and assembly.
DETAILED DESCRIPTION
256 TRaNSCEIVERS ON THE BuS
The standard RS-485 receiver input imped-
ance is 12k (1 unit load), and the standard
driver can drive up to 32 unit loads. The
SP3070E family of transceivers has a /8-
unit load receiver input impedance (96k),
allowing up to 256 transceivers to be con-
nected in parallel on one communication
line. Any combination of these devices as
well as other RS-485 transceivers with a
total of 32 unit loads or fewer can be con-
nected to the line.
REDuCED EMI aND REFlECTIONS
The SP3070E, SP307E and SP3072E
feature reduced slew-rate drivers that mini-
mize EMI and reduce reflections caused by
improperly terminated cables, allowing er-
ror-free data transmission up to 250kbps.
TheSP3073E,SP3074EandSP3075Eoffer
higherdriveroutputslew-ratelimits,allowing
transmit speeds up to 500kbps.
lOW POWER SHuTDOWN MODE
Low-power shutdown mode is initiated by
bringing both RE high and DE low. In shut-
down, the devices typically draw only 50nA
of supply current.
RE and DE can be driven simultaneously;
the parts are guaranteed not to enter shut-
down if RE is high and DE is low for less
than 50ns. If the inputs are in this state for
at least 600ns, the parts are guaranteed to
enter shutdown.
Enable times t
ZH and tZL assume the part was
not in a low-power shutdown state. Enable
times t
ZH(SHDN) and tZL(SHDN) assume the parts
wereshutdown.Ittakesdriversandreceivers
longer to become enabled from low-power
shutdownmodet
ZH(SHDN) and tZL(SHDN) than from
driver/receiver-disable mode (t
ZH, tZL)
DRIVER OuTPuT PROTECTION
Two mechanisms prevent excessive output
current and power dissipation caused by
faults or by bus contention. First, current
limit on the ouput stage, provides immedi-
ate protection against short circuits over the
whole common-mode voltage range.
The major difference between tests done
using the Human Body Model and IEC
6000-4-2 is higher peak current in IEC
6000-4-2, because series resistance is
lower in the IEC 000-4-2 model. Hence,
the ESD withstand voltage measured to
EC 6000-4-2 is generally lower than that
measured using the human body model.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3102R20-7S | CONN RCPT 8POS BOX MNT W/SCKT |
| VE-J5R-MX-S | CONVERTER MOD DC/DC 7.5V 75W |
| VE-22R-IW-F3 | CONVERTER MOD DC/DC 7.5V 100W |
| VE-22R-IW-F2 | CONVERTER MOD DC/DC 7.5V 100W |
| VE-J52-MX-S | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP3075EMN-L/TR | 功能描述:RS-422/RS-485 接口 IC RS485/RS422 Driver/ Receiver Transceiver RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| SP3076E | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:【15kV ESD-Protected, 3.3V, 1/8 Load, Failsafe |
| SP3076EEN | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:15kV ESD-Protected, 3.3V, 1/8 Load, Failsafe RS-485/RS422 Transceivers |
| SP3076EEN/TR | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:15kV ESD-Protected, 3.3V, 1/8 Load, Failsafe RS-485/RS422 Transceivers |
| SP3076EEN-L | 功能描述:RS-422/RS-485 接口 IC RS485/RS422 Driver/ Receiver Transceiver RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。