参数资料
| 型号： | SP6120EY-L |
| 厂商： | Exar Corporation |
| 文件页数： | 14/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 16TSSOP |
| 标准包装： | 95 |
| 系列： | AnyFET™ |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 550kHz |
| 占空比： | 95% |
| 电源电压： | 3 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 管件 |
APPLICATIONS INFORMATION
Inductor Selection
There are many factors to consider in selecting
the inductor including cost, efficiency, size and
EMI. In a typical SP6120 circuit, the inductor is
chosen primarily for value, saturation current
and DC resistance. Increasing the inductor value
will decrease output voltage ripple, but degrade
transient response. Low inductor values pro-
vide the smallest size, but cause large ripple
currents, poor efficiency and more output ca-
pacitance to smooth out the larger ripple cur-
rent. The inductor must also be able to handle
the peak current at the switching frequency
without saturating, and the copper resistance in
the winding should be kept as low as possible to
minimize resistive power loss. A good compro-
mise between size, loss and cost is to set the
inductor ripple current to be within 20% to 40%
of the maximum output current.
The switching frequency and the inductor oper-
ating point determine the inductor value as
follows:
duce considerable ac core loss, especially when
the inductor value is relatively low and the
ripple current is high. Ferrite materials, on the
other hand, are more expensive and have an
abrupt saturation characteristic with the induc-
tance dropping sharply when the peak design
current is exceeded. Nevertheless, they are pre-
ferred at high switching frequencies because
they present very low core loss and the design
only needs to prevent saturation. In general,
ferrite or molypermalloy materials are better
choice for all but the most cost sensitive appli-
cations.
The power dissipated in the inductor is equal to
the sum of the core and copper losses. To mini-
mize copper losses, the winding resistance needs
to be minimized, but this usually comes at the
expense of a larger inductor. Core losses have a
more significant contribution at low output cur-
rent where the copper losses are at a minimum,
and can typically be neglected at higher output
L =
V OUT ( V IN (max) ? V OUT )
V IN (max) F S K r I OUT ( max)
currents where the copper losses dominate. Core
loss information is usually available from the
magnetic vendor.
where:
F S = switching frequency
K r = ratio of the ac inductor ripple current to
the maximum output current
The peak to peak inductor ripple current is:
The copper loss in the inductor can be calculated
using the following equation:
P L ( Cu ) = I L 2 ( RMS ) R WINDING
where I L(RMS) is the RMS inductor current that
can be calculated as follows:
(
I PP =
V OUT ( V IN (max) ? V OUT )
V I N (max) F S L
I L(RMS) = I OUT(max) 1 + 1
3
I PP
I OUT(max)
)
2
Once the required inductor value is selected, the
proper selection of core material is based on
peak inductor current and efficiency require-
ments.
The core material must be large enough not to
saturate at the peak inductor current
I PP
I PEAK = I OUT (max) +
2
and provide low core loss at the high switching
frequency. Low cost powdered iron cores have
a gradual saturation characteristic but can intro-
Output Capacitor Selection
The required ESR (Equivalent Series Resis-
tance) and capacitance drive the selection of the
type and quantity of the output capacitors. The
ESR must be small enough that both the resis-
tive voltage deviation due to a step change in the
load current and the output ripple voltage do not
exceed the tolerance limits expected on the
output voltage. During an output load transient,
the output capacitor must supply all the addi-
tional current demanded by the load until the
Date: 1/21/05
SP6120 Low Voltage, AnyFET TM , Synchronous, Buck Controller
14
? Copyright 2005 Sipex Corporation
相关PDF资料 |
PDF描述 |
|---|---|
| SP6121CN-L | IC REG CTRLR BUCK PWM VM 8NSOIC |
| SP6123CN-L | IC REG CTRLR BUCK PWM VM 8NSOIC |
| SP6125EK1-L/TR | IC REG CTRLR BUCK PWM VM 6TSOT |
| SP6126EK1-L | IC REG CTRLR BUCK PWM VM 6TSOT |
| SP6127EK1-L/TR | IC REG CTRLR BUCK PWM VM 6TSOT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP6120EY-L/TR | 功能描述:DC/DC 开关控制器 Low Voltage, AnyFET Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| SP6120HV | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:High Voltage, Synchronous ,Buck Controller Ideal for 2A to 20A, High Performance, DC-DC Power Converters |
| SP6120HVCY | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:High Voltage, Synchronous ,Buck Controller Ideal for 2A to 20A, High Performance, DC-DC Power Converters |
| SP6120HVCY/TR | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:High Voltage, Synchronous ,Buck Controller Ideal for 2A to 20A, High Performance, DC-DC Power Converters |
| SP6120HVEY | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:High Voltage, Synchronous ,Buck Controller Ideal for 2A to 20A, High Performance, DC-DC Power Converters |
发布紧急采购，3分钟左右您将得到回复。