- 您现在的位置：买卖IC网 > PDF目录17380 > SP6123EB (Exar Corporation)EVAL BOARD FOR SP6123 PDF资料下载
参数资料
| 型号： | SP6123EB |
| 厂商： | Exar Corporation |
| 文件页数： | 11/18页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR SP6123 |
| 标准包装： | 1 |
| 系列： | * |
APPLICATIONS INFORMATION
P CL(max) = R DS(ON) I OUT(max) (1 - D),
P CH(max) = R DS(ON) I OUT(max) D
power sources. Certain tantalum capacitors, such
as AVX TPS series, are surge tested. For generic
tantalum capacitors, use 2:1 voltage derating to
protect the input capacitors from surge fallout.
MOSFET Selection
The losses associated with MOSFETs can be
divided into conduction and switching losses.
Conduction losses are related to the on resis-
tance of MOSFETs, and increase with the load
current. Switching losses occur on each on/off
transition when the MOSFETs experience both
high current and voltage. Since the bottom
MOSFET switches current from/to a paralleled
diode (either its own body diode or an external
Schottky diode), the voltage across the MOSFET
is no more than 1V during switching transition.
As a result, its switching losses are negligible.
The switching losses are difficult to quantify
due to all the variables affecting turn on/off
time. However, making the assumption that the
turn on and turn off transition times are equal,
the transition time can be approximated by:
t T = C ISS V IN ,
I G
where C ISS is the MOSFET’s input capacitance,
or the sum of the gate-to-source capacitance,
C GS , and the drain-to-gate capacitance, C GD .
This parameter can be directly obtained from
the MOSFET’s data sheet.
I G is the gate drive current provided by the
SP6123 (approximately 1A at V IN =5V) and V IN
is the input supply voltage.
Therefore an approximate expression for the
switching losses associated with the high side
MOSFET can be given as:
P SH(max) = (V IN(max) + V F )I OUT(max) t T F S ,
where t T is the switching transition time and V F
is the free wheeling diode drop.
Switching losses need to be taken into account
for high switching frequency, since they are
directly proportional to switching frequency.
The conduction losses associated with top and
bottom MOSFETs are determined by
2
2
where:
P CH(max) = conduction losses of the high side
MOSFET
P CL(max) = conduction losses of the low side
MOSFET
R DS(ON) = drain to source on resistance.
The total power losses of the top MOSFET are
the sum of switching and conduction losses. For
synchronous buck converters of efficiency over
90%, allow no more than 4% power losses for
high or low side MOSFETs. For input voltages
of 3.3V and 5V, conduction losses often domi-
nate switching losses. Therefore, lowering the
R DS(ON) of the MOSFETs always improves effi-
ciency even though it gives rise to higher switch-
ing losses due to increased C ISS .
Total gate charge is the charge required to turn
the MOSFETs on and off under the specified
operating conditions (V GS and V DS ). The gate
charge is provided by the SP6123 gate drive
circuitry. (At 500kHz switching frequency, the
gate charge is the dominant source of power
dissipation in the SP6123). At low output levels,
this power dissipation is noticeable as a reduc-
tion in efficiency. The average current required
to drive the high side and low side MOSFETs is:
I G(av) = Q GH F S + Q GL F S , where
Q GH and Q GL are the total charge for the high
side and the low side MOSFETs respectively.
Considering that the gate charge current comes
from the input supply voltage V IN , the power
dissipated in the SP6123 due to the gate drive is:
P GATE DRIVE = V IN I G(av)
Top and bottom MOSFETs experience unequal
conduction losses if their on time is unequal. For
applications running at large or small duty cycle,
it makes sense to use different top and bottom
MOSFETs. Alternatively, parallel multiple
MOSFETs to conduct large duty factor.
R DS(ON) varies greatly with the gate driver volt-
age. The MOSFET vendors often specify R DS(ON)
on multiple gate to source voltages (V GS ), as
well as provide typical curve of R DS(ON) versus
Date: 9/13/04
SP6123 Low Voltage, Synchronous Step Down PWM Controller
11
? Copyright 2004 Sipex Corporation
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4825ETP+T | IC RELAY DRIVER 8CHAN 20-TQFN |
| MAX4822ETP+T | IC RELAY DRIVER 8CHAN 20-TQFN |
| R1S8-1505/P-R | CONV DC/DC 1W 15VIN 05VOUT |
| SP6121EB | EVAL BOARD FOR SP6121 |
| A9CCA-0408F | FLEX CABLE - AFG04A/AF04/AFG04A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP6123EN-L | 制造商:Exar Corporation 功能描述:IC BUCK CONTROLLER LOW VOLT 300KHZ |
| SP6125 | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:High-Voltage, Step Down Controller in TSOT6 |
| SP6125EB | 功能描述:电源管理IC开发工具 Eval Board for SP6125 Series RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| SP6125EK1L | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:High-Voltage, Step Down Controller in TSOT6 |
| SP6125EK1-L | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。