参数资料
| 型号： | SP6134HEU-L |
| 厂商： | Exar Corporation |
| 文件页数： | 7/15页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 10-MSOP |
| 标准包装： | 50 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 690kHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 其它名称： | 1016-1525-5 SP6134HEU-L-ND |
S P 6 1 3 4 H
H i g h V o l t a g e , 6 0 0 k H z S y n c h r o n o u s P W M S t e p D o w n
C o n t r o l l e r
monitors the positive and negative terminals
of the error amplifier, and if the VFB pin ever
falls more than 250mV (typical) below the
positive reference, a short-circuit fault is set.
Because the SS pin overrides the internal 0.8V
reference during soft start, the SP6134H is
capable of detecting short-circuit faults
throughout the duration of soft start as well as
in regular operation.
H ANDLING OF F AULTS
Upon the detection of power (UVLO), thermal,
or short-circuit faults, the SP6134H is forced
into an idle state where the SS and COMP pins
are pulled low and the gate drivers are held
off. In the event of UVLO fault, the SP6134H
remains in this idle state until the UVLO fault
is removed. Upon the detection of a thermal or
short-circuit fault, an internal 200ms (typical)
timer is activated. In the event of a short-
circuit fault, a restart is attempted
immediately after the 200ms timeout expires.
Whereas, when a thermal fault is detected the
200ms delay continuously recycles and a
restart cannot be attempted until the thermal
fault is removed and the timer expires.
E RROR A MPLIFIER AND V OLTAGE L OOP
As stated before, the heart of the SP6134H
voltage error loop is a high performance, wide
bandwidth transconductance amplifier.
Because of the amplifier’s current limited
(±150 μ A) transconductance, there are many
ways to compensate the voltage loop or to
control the COMP pin externally. A simple,
single pole, single zero compensation can be a
RC to ground. However Exar recommends a
Type II or Type III compensation which
eliminates the g m of the amplifier from the
control loop equations. The amplifier has
enough bandwidth (45° at 4 MHz) and enough
gain (60dB) to run Type III compensation
schemes with adequate gain and phase
margins at cross over frequencies greater than
50kHz.
The common mode output of the error
amplifier is 0.9V to 2.2V. Therefore, the PWM
voltage ramp has been set between 1.1V and
2.2V to ensure proper 0% to 100% duty cycle
capability. The voltage loop also includes two
other very important features. One is an Non-
synchronous start up mode. Basically, the GL
driver can not turn on unless the GH driver
has attempted to turn on or the SS pin has
exceeded 1.7V. This feature prevents the
controller from “dragging down” the output
voltage during startup or in fault modes. The
second feature is a 100% duty cycle timeout
that ensures synchronized refreshing of the
BST capacitor at very high duty ratios. In the
event that the GH driver is on for 20
continuous clock cycles, a reset is given to the
PWM flip flop half way through the 21st cycle.
This forces GL to rise for the remainder of the
cycle, in turn refreshing the BST capacitor.
G ATE D RIVERS
The SP6134H contains a pair of powerful 2 Ω
SOURCE and 1.5 Ω SINK drivers. These state
of the art drivers are designed to drive
external NFETs capable of handling up to 30A.
Rise, fall, and non-overlap times have all been
minimized to achieve maximum efficiency. All
drive pins GH, GL & SWN are monitored
continuously to ensure that only one external
NFET is ever on at any given time.
? 2008 Exar Corporation
7/15
Rev. 2.0.0
相关PDF资料 |
PDF描述 |
|---|---|
| SP6136ER1-L/TR | IC REG CTRLR BUCK PWM VM 16-QFN |
| SP6137EU-L | IC REG CTRLR BUCK PWM VM 10-MSOP |
| SP6201EM5-G-3-3 | IC REG LDO 3.3V .2A SOT23-5 |
| SP6203EM5-L | IC REG LDO ADJ .3A SOT23-5 |
| SP6214EC5-L-3-3 | IC REG LDO 3.3V .1A SC70-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP6134HEU-L/TR | 功能描述:电压模式 PWM 控制器 High Voltage,600 kHz Synchronous RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| SP6134HV | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Dual Supply Synchronous Buck Controller |
| SP6134HVLED | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP6134HVLEDEB | 功能描述:电源管理IC开发工具 Dual Supply Sync Buck Controller RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| SP6136 | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Evaluation Board Manual |
发布紧急采购，3分钟左右您将得到回复。