- 您现在的位置：买卖IC网 > PDF目录17175 > SP6134HVLEDEB (Exar Corporation)EVAL BOARD FOR SP6134HVLED PDF资料下载
参数资料
| 型号： | SP6134HVLEDEB |
| 厂商： | Exar Corporation |
| 文件页数： | 4/15页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR SP6134HVLED |
| 标准包装： | 1 |
| 系列： | * |
S P 6 1 3 4 H
H i g h V o l t a g e , 6 0 0 k H z S y n c h r o n o u s P W M S t e p D o w n
C o n t r o l l e r
PIN ASSIGNEMENT
Fig. 3: SP6134H Pin Assignment
PIN DESCRIPTION
Name
V CC
GL
GND
VFB
COMP
UVIN
SS
SWN
GH
BST
Pin Number
1
2
3
4
5
6
7
8
9
10
Description
Bias Supply Input. Connect to external 5V supply. Used to power internal circuits and
low side gate driver.
High current driver output for the low side NFET switch. It is always low if GH is high or
during a fault. Resistor pull down ensure low state at low voltage.
Ground Pin. The control circuitry of the IC and lower power driver are referenced to this
pin. Return separately from other ground traces to the (-) terminal of COUT.
Feedback Voltage and Short Circuit Detection pin. It is the inverting input of the Error
Amplifier and serves as the output voltage feedback point for the Buck Converter. The
output voltage is sensed and can be adjusted through an external resistor divider.
Whenever VFB drops 0.25V below the positive reference, a short circuit fault is detected
and the IC enters hiccup mode.
Output of the Error Amplifier. It is internally connected to the inverting input of the
PWM comparator. An optimal filter combination is chosen and connected to this pin and
either ground or VFB to stabilize the voltage mode loop.
UVLO input for VIN voltage. Connect a resistor divider between VIN and UVIN to set
minimum operating voltage.
Soft Start. Connect an external capacitor between SS and GND to set the soft start rate
based on the 10 μ A source current. The SS pin is held low via a 1mA (min) current
during all fault conditions.
Lower supply rail for the GH high-side gate driver. Connect this pin to the switching
node at the junction between the two external power MOSFET transistors.
High current driver output for the high side NFET switch. It is always low if GL is high or
during a fault. Resistor pull down ensure low state at low voltage.
High side driver supply pin. Connect BST to the external boost diode and capacitor as
shown in the Typical Application Circuit on page 1. High side driver is connected
between BST pin and SWN pin.
? 2008 Exar Corporation
4/15
Rev. 2.0.0
相关PDF资料 |
PDF描述 |
|---|---|
| R0.25S8-0512/P-R | CONV DC/DC 0.25W 5V IN 12V OUT |
| R1S12-3.312/H-R | CONV DC/DC 1W 3.3VIN 12VOUT |
| R0.25S8-0509/P-R | CONV DC/DC 0.25W 5V IN 9V OUT |
| R0.25S8-0505/P-R | CONV DC/DC 0.25W 5V IN 5V OUT |
| R0.25S12-123.3-R | CONV DC/DC 0.25W 12V IN 3.3V OUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP6136 | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP6136_06 | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP6136EB | 功能描述:DC/DC 开关控制器 Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| SP6136ER1 | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP6136ER1/TR | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Synchronous Buck Controller |
发布紧急采购，3分钟左右您将得到回复。