参数资料
| 型号： | SP6203EM5-L |
| 厂商： | Exar Corporation |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .3A SOT23-5 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 可调至 1.25V |
| 输入电压： | 2.7 V ~ 5.5 V |
| 电压 - 压降（标准）： | 0.18V @ 300mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA |
| 电流 - 限制（最小）： | 330mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 散装 |
| 其它名称： | 1016-1396 |
S P 6 2 0 3 / S P 6 2 0 5
3 0 0 m A / 5 0 0 m A L o w N o i s e C M O S L D O R e g u l a t o r s
time (T WU ) and the settling time (T S ). The
wake up time is defined as the time it takes
for the output to rise to 2% of its total value
after being released from shutdown (E N >
0.4V). The settling time is defined as the
condition where the output reaches 98% of its
total value after being released from
shutdown. The latter is also called the turn on
time and is dependent on the output capacitor,
a little bit on load and, if present, on a bypass
capacitor.
T URN O FF T IME
The turn off time is defined as the condition
where the output voltage drops about 66% ( θ )
of its total value. 5 θ to 7 θ is the constant
where the output voltage drops nearly to zero.
There will always be a small voltage drop in
shutdown because of the switch unless we
short-circuit it. The turn off time of the output
voltage is dependent on load conditions,
output capacitance on V OUT (time constant ? =
R L C L ) and also on the difference in voltage
between input and output.
T HERMAL C ONSIDERATIONS
The SP6203/6205 is designed to provide
300/500mA of continuous current in a tiny
package. Maximum power dissipation can be
calculated based on the output current and the
voltage drop across the part. To determine the
maximum power dissipation of the package,
use the junction-to-ambient thermal
resistance of the device and the following
basic equation:
P D = (T J(max) - T A ) / θ JA
T J(max) is the maximum junction temperature of
the die and is 125°C. T A is the ambient
temperature. θ JA is the junction-to-ambient
thermal resistance for the regulator and is
layout dependent. The SOT-23-5 package has
a θ JA of approximately 191°C/W for minimum
PCB copper footprint area.
This results in a maximum power dissipation
of:
P D(max) =[(125°C-25°C)/(191°C/W)] = 523mW
The actual power dissipation of the regulator
circuit can be determined using one simple
equation:
P D = (V IN - V OUT ) * I OUT + V IN * I GND
To prevent the device from entering thermal
shutdown, maximum power dissipation cannot
be exceeded.
Substituting P D(max) for P D and solving for the
operating conditions that are critical to the
application will give the maximum operating
conditions for the regulator circuit. For
example, if we are operating the SP6203 3.0V
at room temperature, with a minimum
footprint layout and output current of 300mA,
the maximum input voltage can be
determined, based on the equation below.
Ground pin current can be taken from the
electrical specifications table (0.23mA at
300mA).
390mW = (V IN -3.0V) * 300mA + V IN *0.23mA
After calculations, we find that the maximum
input voltage of a 3.0V application at 300mA
of output current in a SOT-23-5 package is
4.7V.
So if the intent is to operate a 5V output
version from a 6V supply at 300mA load and
at a 25°C ambient temperature, then the
actual total power dissipation will be:
P D =([6V-5V]*[300mA])+(6V*0.23mA)=301.4mW
This is well below the 523mW package maxi-
mum. Therefore, the regulator can be used.
Note that the regulator cannot always be used
at its maximum current rating. For example, in
a 5V input to 3.0V output application at an
ambient temperature of 25°C and operating at
the full 500mA (I GND =0.355mA) load, the
regulator is limited to a much lower load
current, determined by the following equation:
523mW = ( [5V-3V]*[ I load(max) ]) +(5V*0.350mA)
? 2012 Exar Corporation
10/14
Rev. 2.0.0
相关PDF资料 |
PDF描述 |
|---|---|
| SP6214EC5-L-3-3 | IC REG LDO 3.3V .1A SC70-5 |
| SP6260BEK-L/TR | IC REG LDO 1.8V .2A SOT23-5 |
| SP6265MER-L/TR | IC REG LDO 1.8V/2.8V .15A 8DFN |
| SP6330EK1-L-X-J-C/TR | IC SUPERVISOR WATCHDOG 8TSOT |
| SP6641AEK-L-3-3 | IC REG BOOST SYNC 3.3V SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP6203EM5-L/TR | 功能描述:低压差稳压器 - LDO Low Noise 300mA CMOS LDO Regulators RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| SP6203EM5-L-2-5 | 功能描述:低压差稳压器 - LDO Micropower, 300mA CMOS LDO Regulators RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| SP6203EM5-L-2-5/TR | 功能描述:低压差稳压器 - LDO Low Noise 300mA CMOS LDO Regulators RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| SP6203EM5-L-2-7 | 制造商:Exar Corporation 功能描述: |
| SP6203EM5-L-2-8 | 功能描述:低压差稳压器 - LDO Micropower, 300mA CMOS LDO Regulators RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。