参数资料
| 型号： | SP721AP |
| 厂商： | Littelfuse Inc |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | TVS ARRAY ESD 6 INPUT 8-DIP |
| 标准包装： | 1,000 |
| 系列： | SP721 |
| 电压 - 工作： | 30V |
| 技术： | 混合技术 |
| 电路数： | 6 |
| 应用： | 通用 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 其它名称： | F2166 |
TVS Diode Arrays
Electronic Protection Array for ESD and Overvoltage Protection
SP721
Absolute Maximum Ratings
Thermal Information
Continuous Supply Voltage, (V+) - (V-). . . . . . . . . . . . . . . . . . . . . . . . . +35V
Thermal Resistance (Typical, Note 1)
θ JA ( o C/W)
Forward Peak Current, IIN to VCC , IIN to GND
(Refer to Figure 6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±2A, 100μs
ESD Ratings and Capability (Figure 1, Table 1)
Load Dump and Reverse Battery (Note 2)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Maximum Storage Temperature Range . . . . . . . . . . . . . . . . . . . . -65 o C to 150 o C
Maximum Junction Temperature (Plastic Package) . . . .. . . . . . . . . . . . . . . . 150 o C
Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . . . .. . . . . . . . . . . .300 o C
(SOIC Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device
at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θ JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications T A = -40 o C to 105 o C, VIN = 0.5VCC , Unless Otherwise Specified
PARAMETER
Operating Voltage Range,
SYMBOL
V SUPPLY
TEST CONDITIONS
MIN
-
TYP
2 to 30
MAX
-
UNITS
V
V SUPPLY = [(V+) - (V-)]
Forward Voltage Drop
IN to V-
IN to V+
V FWDL
V FWDH
I IN = 1A (Peak Pulse)
-
-
2
2
-
-
V
V
Input Leakage Current
Quiescent Supply Current
Equivalent SCR ON Threshold
Equivalent SCR ON Resistance
Input Capacitance
Input Switching Speed
I IN
I QUIESCENT
C IN
t ON
Note 3
V FWD /I FWD ; Note 3
-20
-
-
-
-
-
5
50
1.1
1
3
2
+20
200
-
-
-
-
nA
nA
V
?
pF
ns
5
NOTES:
2. In automotive and battery operated systems, the power supply lines should be externally protected for load dump and reverse battery. When the
V+ and V- Pins are connected to the same supply voltage source as the device or control line under protection, a current limiting resistor should
be connected in series between the external supply and the SP721 supply pins to limit reverse battery current to within the rated maximum
limits. Bypass capacitors of typically 0.01 μ F or larger from the V+ and V- Pins to ground are recommended.
3. Refer to the Figure 3 graph for definitions of equivalent “SCR ON Threshold” and “SCR ON Resistance”. These characteristics are given here
for thumb-rule information to determine peak current and dissipation under EOS conditions.
ESD Capability
TABLE 1. ESD TEST CONDITIONS
ESD capability is dependent on the application and defined test standard.The
STANDARD
TYPE/MODE
R D
C D
± V D
evaluation results for various test standards and methods based on Figure 1
are shown in Table 1.
MIL-STD-3015.7 Modified HBM
Standard HBM
1.5k ? 100pF 15kV
1.5k ? 100pF 6kV
For the “Modified” MIL-STD-3015.7 condition that is defined as an “in-circuit”
method of ESD testing, the V+ and V- pins have a return path to ground and
IEC 61000-4-2
HBM, Air Discharge
330 ? 150pF 15kV
the SP721 ESD capability is typically greater than 15kV from 100pF through
1.5k ? . By strict definition of MIL-STD-3015.7 using “pin-to-pin” device testing,
the ESD voltage capability is greater than 6kV. The MIL-STD-3015.7 results
HBM, Direct Discharge
HBM, Direct Discharge,
Two Parallel Input Pins
330 ? 150pF
330 ? 150pF
4kV
8kV
were determined from AT&T ESD Test Lab measurements.
EIAJ IC121
Machine Model
0k ?
200pF
1kV
The HBM capability to the IEC 61000-4-2 standard is greater than 15kV
for air discharge (Level 4) and greater than 4kV for direct discharge
R 1
R D
(Level 2). Dual pin capability (2 adjacent pins in parallel) is well in excess
of 8kV (Level 4).
For ESD testing of the SP721 to EIAJ IC121 Machine Model (MM) standard,
the results are typically better than 1kV from 200pF with no series resistance.
CHARGE
SWITCH
H.V.
SUPPLY
± V D
C D
DISCHARGE
SWITCH
IN
DUT
IEC 1000-4-2: R 1 50 to 100M ?
MIL-STD-3015.7: R 1 1 to 10M ?
FIGURE 1. ELECTROSTATIC DISCHARGE TEST
w w w. l i t t e l f u s e . c o m
235
相关PDF资料 |
PDF描述 |
|---|---|
| TA35-CFTWM030C0 | CIRC BREAKER/WHITE ROCKER SP 3A |
| SP721AB | TVS ARRAY ESD 6 INPUT 8-SOIC |
| TA35-CFTWF130C0 | CIRC BREAKER/WHITE ROCKER SP 13A |
| SP720AP | TVS ARRAY ESD 14 INPUT 16-DIP |
| EL2126CS | IC AMP WIDEBAND LP LN 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP721APG | 制造商:LITTELFUSE 制造商全称:Littelfuse 功能描述:SP721 Series 3pF 4kV Diode Array |
| SP721APP | 功能描述:TVS二极管阵列 6 CH DIODE ARRAY RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C |
| SP721APP | 制造商:Littelfuse 功能描述:TVS DIODE ARRAY |
| SP721APP | 制造商:Littelfuse 功能描述:TVS Diode Array |
| SP721APP | 制造商:Littelfuse 功能描述:THYRISTOR ARRAY TVS |
发布紧急采购，3分钟左右您将得到回复。