- 您现在的位置：买卖IC网 > Datasheet目录1009 > SP7600EB (Exar Corporation)EVAL BOARD FOR SP7600 Datasheet资料下载
参数资料
| 型号： | SP7600EB |
| 厂商： | Exar Corporation |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR SP7600 |
| 标准包装： | 1 |
| 电流 - 输出 / 通道： | 2A |
| 输出及类型： | 1，非隔离 |
| 特点： | PWM 亮度控制 |
| 输入电压： | 4.5 ~ 29 V |
| 已供物品： | 板 |
| 已用 IC / 零件： | SP7600 |
| 相关产品： | SP7600EN2-L/TR-ND - IC LED DRVR PWM STP-DWN 8HNSOIC 1016-1896-5-ND - IC LED DRVR PWM STP-DWN 8HNSOIC |
| 其它名称： | 1016-1233 |
_______________________________________________ USING THE EVALUATION BOARD
1) Powering Up the SP7600 Circuit
The SP7600 Evaluation Board can be powered from a 4.5V to 29V power supply. Connect the power
supply with short leads directly to the “Vin” and “GND” posts.
2) Setting the output current
Externally connected LEDs need to be connected anode to the VOUT pin and cathode to the Vfb pin. As
many as 6 series connected LEDs may be used, depending on the input voltage range available. The
maximum output current is 3A but the user should take care not to exceed the maximum junction
temperature, 125°C. Up to 2A maximum is possible in almost all conditions. The board also has SMT
pads available for LEDs to be mounted in the LED1 position for a Luxeon K2 LED, and LED2, LED3 and
LED4 positions for Luxeon Rebel LEDs. The total output current of the SP7600 is controlled by the VFB
pin voltage setpoint of 200mV. Use a resistor at RA to set the output current by the formula:
Iout = Vfb/RA
where RA is the parallel combination of Ra and any of the resistors Rb, Rc or Rd.
If Ra, Rb, Rc and Rd are used then RA = 1/(1/Ra + 1/Rb + 1/Rc + 1/Rd)
Standard SP7600EB Evaluation Board Example :
Iout = Vfb/RA = 200mV/0.22ohm = 1A
3) Dimming
The SP7600 can be pulse width modulated using a signal applied to the DIM post. The DIM signal
connects to the VFB pin through a 1N4148 diode and will shutdown the SP7600 when DIM = H and turn-
on the SP7600 when DIM = L. The DIM signal needs to be greater than 600mV minimum to turn-off the
SP7600 and less than 200mV to fully turn-on the SP7600. It is recommended to use a signal with DIM =
1V or more for OFF and 0V for ON. The user should note that the logic is reversed relative to many
other PWM controlled LED drivers. In other words a logic level high at 20% duty cycle will result in
approximately an 80% duty cycle for the LED. Recommended modulation frequencies are from 100Hz to
200Hz with 10 – 90% duty cycle, 500Hz with 10 – 80% duty cycle, and 1000Hz with 10 – 70% duty cycle.
Figures 2 & 3 show the output response at the maximum PWM DIM signal of 1000Hz. See figure 4 for
100Hz to 1000Hz duty cycle response for two Luxeon K2 LEDs in parallel at 2A total current.
12/17/07
SP7600 Evaluation Board Manual
Page 2 of 5
? 2007 Exar Corporation
相关PDF资料 |
PDF描述 |
|---|---|
| SP7601EB | EVAL BOARD FOR SP7601 |
| SP7616EB | EVAL BOARD FOR SP7616 |
| SP7648EB | EVAL BOARD FOR SP7648 |
| SP7685EB | EVAL BOARD FOR SP7665 |
| SP7686EB | EVAL BOARD FOR SP7666 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP7600EN2-L | 功能描述:LED照明驱动器 Applications RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| SP7600EN2-L/TR | 功能描述:LED照明驱动器 2A 29V NON-SYNC BUCK HIGH PWR RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| SP7601 | 制造商:EXAR 制造商全称:EXAR 功能描述:29V High Voltage LED Driver |
| SP7601_EB | 制造商:EXAR 制造商全称:EXAR 功能描述:29V High Voltage LED Driver |
| SP7601EB | 功能描述:LED 照明开发工具 Eval Board for SP7601 Series RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。