- 您现在的位置：买卖IC网 > PDF目录10943 > SPC5607BF1MLU6 (Freescale Semiconductor)IC MCU 32BIT 1.5MB FLASH 176LQFP PDF资料下载
参数资料
| 型号： | SPC5607BF1MLU6 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 17/112页 |
| 文件大小： | 0K |
| 描述： | IC MCU 32BIT 1.5MB FLASH 176LQFP |
| 标准包装： | 200 |
| 系列： | MPC56xx Qorivva |
| 核心处理器： | e200z0h |
| 芯体尺寸： | 32-位 |
| 速度： | 64MHz |
| 连通性： | CAN，I²C，LIN，SCI，SPI |
| 外围设备： | DMA，POR，PWM，WDT |
| 输入/输出数： | 149 |
| 程序存储器容量： | 1.5MB（1.5M x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 96K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 5.5 V |
| 数据转换器： | A/D 29x10b，5x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 176-LQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页
MPC5607B Microcontroller Data Sheet, Rev. 7
Package pinouts and signal descriptions
Freescale Semiconductor
12
3.3
Pad configuration during standby mode exit
Pad configuration (input buffer enable, pull enable) for low-power wakeup pads is controlled by both the SIUL and WKPU
modules. During standby exit, all low power pads PA[0,1,2,4,15], PB[1,3,8,9,10]1, PC[7,9,11], PD[0,1], PE[0,9,11],
PF[9,11,13]2, PG[3,5,7,9]2, PI[1,3]3 are configured according to their respective configuration done in the WKPU module. All
other pads will have the same configuration as expected after a reset.
The TDO pad has been moved into the STANDBY domain in order to allow low-power debug handshaking in STANDBY
mode. However, no pull-resistor is active on the TDO pad while in STANDBY mode. At this time the pad is configured as an
input. When no debugger is connected the TDO pad is floating causing additional current consumption.
To avoid the extra consumption TDO must be connected. An external pull-up resistor in the range of 47–100 kOhms should be
added between the TDO pin and VDD. Only if the TDO pin is used as an application pin and a pull-up cannot be used should
a pull-down resistor with the same value be used instead between the TDO pin and GND.
3.4
Voltage supply pins
Voltage supply pins are used to provide power to the device. Three dedicated VDD_LV/VSS_LV supply pairs are used for 1.2 V
regulator stabilization.
1. PB[8, 9] ports have wakeup functionality in all modes except STANDBY.
2. PF[9,11,13], PG[3,5,7,9], PI[1,3] are not available in the 100-pin LQFP.
3. PI[1,3] are not available in the 144-pin LQFP.
Table 3. Voltage supply pin descriptions
Port pin
Function
Pin number
100 LQFP
144 LQFP
176 LQFP
208 MAPBGA
VDD_HV
Digital supply voltage
15, 37, 70, 84
19, 51, 100,
123
6, 27, 59, 85,
124, 151
C2, D9, E16,
G13, H3, N4,
N9, R5
VSS_HV
Digital ground
14, 16, 35, 69,
83
18, 20, 49, 99,
122
7, 26, 28, 57,
86, 123, 150
G7, G8, G9,
G10, H7, H8,
H9, H10, J7,
J8, J9, J10,
K7, K8, K9,
K10
VDD_LV
1.2 V decoupling pins. Decoupling
capacitor must be connected
between these pins and the nearest
VSS_LV pin.
1
19, 32, 85
23, 46, 124
31, 54, 152
D8, K4, P7
VSS_LV
1.2 V decoupling pins. Decoupling
capacitor must be connected
between these pins and the nearest
VDD_LV pin.
1
18, 33, 86
22, 47, 125
30, 55, 153
C8, J2, N7
VDD_BV
Internal regulator supply voltage
20
24
32
K3
VSS_HV_ADC0 Reference ground and analog ground
for the A/D converter 0 (10-bit)
51
73
89
R15
VDD_HV_ADC0 Reference voltage and analog supply
for the A/D converter 0 (10-bit)
52
74
90
P14
VSS_HV_ADC1 Reference ground and analog ground
for the A/D converter 1 (12-bit)
59
81
98
N12
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B2N-IW-B1 | CONVERTER MOD DC/DC 18.5V 100W |
| VE-B2M-IW-B1 | CONVERTER MOD DC/DC 10V 100W |
| VE-B2H-IX-B1 | CONVERTER MOD DC/DC 52V 75W |
| PCM3168APAPRG4 | IC 24-BIT AUDIO CODEC 64-HTQFP |
| VE-B23-IW-B1 | CONVERTER MOD DC/DC 24V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SPC5607BF1VLU6 | 制造商:Freescale Semiconductor 功能描述: |
| SPC5607CECLLR | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontroller |
| SPC5607CECLQR | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontroller |
| SPC5607CECLUR | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontroller |
| SPC5607CEMLLR | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontroller |
发布紧急采购，3分钟左右您将得到回复。