- 您现在的位置：买卖IC网 > PDF目录17505 > SPM6530T-R68M140 (TDK Corporation)INDUCTOR .68UH 14A 20% SMD PDF资料下载
参数资料
| 型号： | SPM6530T-R68M140 |
| 厂商： | TDK Corporation |
| 文件页数： | 2/25页 |
| 文件大小： | 0K |
| 描述： | INDUCTOR .68UH 14A 20% SMD |
| 产品目录绘图： | SPM6530 Series Top SPM6530 Series Side SPM6530 Series Footprint |
| 特色产品： | SPM5030 and SPM6530 Series Power Inductors |
| 标准包装： | 1 |
| 系列： | SPM |
| 电感： | 680nH |
| 电流： | 14A |
| 电流 - 温升： | 16A |
| 容差： | ±20% |
| 屏蔽： | 屏蔽 |
| DC 电阻(DCR)： | 最大 5.39 毫欧 |
| 封装/外壳： | 0.280" L x 0.256" W x 0.118" H（7.10mm x 6.50mm x 3.00mm） |
| 安装类型： | 表面贴装 |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 125°C |
| 频率 - 测试： | 100kHz |
| 产品目录页面： | 1815 (CN2011-ZH PDF) |
| 其它名称： | 445-3879-6 |
(2/25)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
001-01 / 20131226 / inductor_commercial_power_spm_en.fm
相关PDF资料 |
PDF描述 |
|---|---|
| EEM28DRKI | CONN EDGECARD 56POS DIP .156 SLD |
| ESM08DREI | CONN EDGECARD 16POS .156 EYELET |
| ABM11-30.000MHZ-D2X-T3 | CRYSTAL 30.000 MHZ 10PF SMD |
| PVA2A222A01B00 | TRIMMER 2.2K OHM 0.1W SMD |
| PVA2A221A01B00 | TRIMMER 220 OHM 0.1W SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SPM6550T-1R0 | 制造商:IRF 制造商全称:International Rectifier 功能描述:USER GUIDE FOR IR3898 EVALUATION BOARD |
| SPM6550T-1R0M | 制造商:IRF 制造商全称:International Rectifier 功能描述:4A Highly Integrated SupIRBuck Singlea??Input Voltage |
| SPM6550T-1R0M100A | 制造商:IRF 制造商全称:International Rectifier 功能描述:HIGHLY EFFICIENT INTEGRATED 6A, SYNCHRONOUS BUCK REGULATOR |
| SPM6550T-2R2M | 功能描述:2.2μH Shielded Wirewound Inductor 13.4A 10.7 mOhm Max 2-SMD, J-Lead 制造商:tdk corporation 系列:SPM 包装:剪切带（CT） 零件状态:在售 类型:绕线 材料 - 磁芯:金属 电感:2.2μH 容差:±20% 额定电流:13.4A 电流 - 饱和值:7.9A 屏蔽:屏蔽 DC 电阻（DCR）:10.7 毫欧最大 不同频率时的 Q 值:- 频率 - 自谐振:- 等级:- 工作温度:-40°C ~ 125°C 频率 - 测试:100kHz 安装类型:表面贴装 封装/外壳:2-SMD，J 形引线 大小/尺寸:0.280" 长 x 0.256" 宽（7.10mm x 6.50mm） 高度 - 安装（最大值）:0.203"（5.15mm） 标准包装:1 |
| SPM6550T-4R7M | 功能描述:4.7μH Shielded Wirewound Inductor 7A 23.7 mOhm Max 2-SMD, J-Lead 制造商:tdk corporation 系列:SPM 包装:剪切带（CT） 零件状态:在售 类型:绕线 材料 - 磁芯:金属 电感:4.7μH 容差:±20% 额定电流:7A 电流 - 饱和值:7.6A 屏蔽:屏蔽 DC 电阻（DCR）:23.7 毫欧最大 不同频率时的 Q 值:- 频率 - 自谐振:- 等级:- 工作温度:-40°C ~ 125°C 频率 - 测试:100kHz 安装类型:表面贴装 封装/外壳:2-SMD，J 形引线 大小/尺寸:0.280" 长 x 0.256" 宽（7.10mm x 6.50mm） 高度 - 安装（最大值）:0.203"（5.15mm） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。