- 您现在的位置：买卖IC网 > PDF目录382545 > SPT9689BCU (SIGNAL PROCESSING TECHNOLOGIES) DUAL ULTRAFAST VOLTAGE COMPARATOR PDF资料下载
参数资料
| 型号： | SPT9689BCU |
| 厂商： | SIGNAL PROCESSING TECHNOLOGIES |
| 元件分类： | 运动控制电子 |
| 英文描述： | DUAL ULTRAFAST VOLTAGE COMPARATOR |
| 中文描述： | DUAL COMPARATOR, 30000 uV OFFSET-MAX, UUC |
| 封装： | DIE |
| 文件页数： | 3/8页 |
| 文件大小： | 75K |
| 代理商： | SPT9689BCU |
3
2/20/01
SPT9689
!
"#
"#
"#
$
$
$
$
$
%&&'(')$%*+
),$-+$*.'
,$,$
,$,$
$
!
$
/
/
*$01)*2+'
*$01)*2+'
TEST LEVEL CODES
All electrical characteristics are subject to the
following conditions:
All parameters having min/max specifications
are guaranteed. The Test Level column indi-
cates the specific device testing actually per-
formed during production and Quality Assur-
ance inspection. Any blank section in the data
column indicates that the specification is not
tested at the specified condition.
LEVEL
TEST PROCEDURE
I
100% production tested at the specified temperature.
100% production tested at T
A
= +25
°
C, and sample tested at the
specified temperatures.
QA sample tested only at the specified temperatures.
Parameter is guaranteed (but not tested) by design and characteri-
zation data.
Parameter is a typical value for information purposes only.
100% production tested at T
A
= +25
°
C. Parameter is guaranteed
over specified temperature range.
II
III
IV
V
VI
TIMING INFORMATION
The timing diagram for the comparator is shown in figure
1. If LE is high and LE low in the SPT9689, the comparator
tracks the input difference voltage. When LE is driven low
and LE high, the comparator outputs are latched into their
existing logic states.
The leading edge of the input signal (which consists of a
20 mV overdrive voltage) changes the comparator output
after a time of t
pdL
or t
pdH
(Q or Q). The input signal must
be maintained for a time t
S
(set-up time) before the LE fall-
ing edge and LE rising edge and held for time t
H
after the
falling edge for the comparator to accept data. After t
H
, the
output ignores the input status until the latch is strobed
again. A minimum latch pulse width of t
pL
is needed for
strobe operation, and the output transitions occur after a
time of t
pLOH
or t
pLOL
.
The set-up and hold times are a measure of the time
required for an input signal to propagate through the first
stage of the comparator to reach the latching circuitry.
Input signals occurring before t
S
will be detected and held;
those occurring after t
H
will not be detected. Changes
between t
S
and t
H
may not be detected.
Figure 1 – Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| SPT9689BIC | DUAL ULTRAFAST VOLTAGE COMPARATOR |
| SPT9689BIP | DUAL ULTRAFAST VOLTAGE COMPARATOR |
| SPT9712 | 12-BIT, 100 MWPS ECL D/A CONVERTER |
| SPT9712AIP | 12-BIT, 100 MWPS ECL D/A CONVERTER |
| SPT9712BIP | 12-BIT, 100 MWPS ECL D/A CONVERTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SPT9689BIC | 功能描述:校验器 IC VOLTAGE COMPARATOR <100ps 5-50mV 10V/ns RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| SPT9689BIJ | 功能描述:校验器 IC VOLTAGE COMPARATOR <100ps 5-50mV 10V/ns RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| SPT9689BIP | 功能描述:校验器 IC Dual Comparator High Speed RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| SPT9691 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:WIDE INPUT VOLTAGE, JFET COMPARATOR |
| SPT9691SCC | 功能描述:校验器 IC JFET COMPARATR 2.5ns <100pA -4 - +8V RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。