参数资料
| 型号： | SQ24S15033-NS0S |
| 厂商： | Power-One |
| 文件页数： | 3/70页 |
| 文件大小： | 0K |
| 描述： | DC/DC EIGHTH BRICK 3.3V OUT |
| 标准包装： | 10 |
| 系列： | * |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
SQ24 Series DC-DC Converter Data Sheet
18-36 VDC Input; Standard Outputs from 1-12 VDC
Operation
Input and Output Impedance
in which case it must be capable of sourcing or sinking up to
1mA depending on the signal polarity. See the Start-up
Information section for system timing waveforms associated
with use of the ON/OFF pin.
These power converters have been designed to be stable
with no external capacitors when used in low inductance
input and output circuits.
However, in many applications, the inductance associated
with the distribution from the power source to the input of the
converter can affect the stability of the converter. The
addition of a 100 μF electrolytic capacitor with an ESR < 1 ?
across the input helps ensure stability of the converter. In
many applications, the user has to use decoupling
capacitance at the load. The power converter will exhibit
Remote Sense (Pins 5 and 7)
The remote sense feature of the converter compensates for
voltage drops occurring between the output pins of the
converter and the load. The SENSE(-) (Pin 5) and SENSE(+)
(Pin 7) pins should be connected at the load or at the point
where regulation is required (see Fig. B).
Semi Q Family
stable operation with external load capacitance up to
1000 μF on 12 V, 2,200 μF on 8.0 V, 10,000 μF on 5.0 V –
6.0 V, and 15,000 μF on 3.3 V – 1.0 V outputs.
ON/OFF (Pin 2)
Vin
Vin (+)
ON/OFF
Vin (-)
TM
Converter
(Top View)
Vout (+)
100
SENSE (+)
TRIM
SENSE (-)
10
Vout (-)
Rw
Rw
Rload
The ON/OFF pin is used to turn the power converter on or
off remotely via a system signal. There are two remote
control options available, positive logic and negative logic
and both are referenced to Vin(-). Typical connections are
shown in Fig. A.
Fig. B: Remote sense circuit configuration.
If remote sensing is not required, the SENSE(-) pin must be
connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin
Semi Q Family
Vin
CONTROL
Vin (+)
ON/OFF
Vin (-)
TM
Converter
(Top View)
Vout (+)
SENSE (+)
TRIM
SENSE (-)
Vout (-)
Rload
must be connected to the Vout(+) pin (Pin 8) to ensure the
converter will regulate at the specified output voltage. If
these connections are not made, the converter will deliver an
output voltage that is slightly higher than the specified value.
Because the sense leads carry minimal current, large traces
on the end-user board are not required. However, sense
INPUT
Fig. A: Circuit configuration for ON/OFF function.
The positive logic version turns on when the ON/OFF pin is
at logic high and turns off when at logic low. The converter is
on when the ON/OFF pin is left open .
The negative logic version turns on when the pin is at logic
low and turns off when the pin is at logic high. The ON/OFF
pin can be hard wired directly to Vin(-) to enable automatic
power up of the converter without the need of an external
control signal.
ON/OFF pin is internally pulled-up to 5 V through a resistor.
A mechanical switch, open collector transistor, or FET can
be used to drive the input of the ON/OFF pin. The device
must be capable of sinking up to 0.2mA at a low level
voltage of ? 0.8V. An external voltage source ( ± 20V
maximum) may be connected directly to the ON/OFF input,
traces should be located close to a ground plane to minimize
system noise and insure optimum performance. When wiring
discretely, twisted pair wires should be used to connect the
sense lines to the load to reduce susceptibility to noise.
The converter’s output over-voltage protection (OVP) senses
the voltage across Vout(+) and Vout(-), and not across the
sense lines, so the resistance (and resulting voltage drop)
between the output pins of the converter and the load should
be minimized to prevent unwanted triggering of the OVP.
When utilizing the remote sense feature, care must be taken
not to exceed the maximum allowable output power
capability of the converter, equal to the product of the
nominal output voltage and the allowable output current for
the given conditions.
When using remote sense, the output voltage at the
converter can be increased by as much as 10% above the
nominal rating in order to maintain the required voltage
across the load. Therefore, the designer must, if necessary,
MCD10159 Rev. 1.2, 20-Apr-12
Page 3 of 70
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| OSTTS24A15D | TERM BLOCK PLUG 7.5MM 24POS |
| OSTTS24A15C | TERM BLOCK PLUG 7.5MM 24POS |
| PSS5A12-7 | SWITCHING REGULATOR 61.2W 5.1V |
| OSTH416505C | CONN PLUG HEADER 16PS 5.08MM |
| MC14025BFELG | IC GATE NOR TRPL 3INPUT 14SOEIAJ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SQ24S15033-PS00 | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQ24S15033-PS00A | 制造商:Power-One 功能描述: |
| SQ24S15033PS00G | 制造商:Power-One 功能描述: |
| SQ24S15033-PS00G | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQ24S15033-PS00GA | 制造商:Power-One 功能描述: |
发布紧急采购，3分钟左右您将得到回复。