参数资料
型号: SQ48S03150-PS00
厂商: Power-One
文件页数: 4/64页
文件大小: 0K
描述: DC/DC EIGHTH BRICK
标准包装: 100
系列: *
SQ48 DC-DC Series Data Sheet
36-75 VDC Input; 1.0-12 VDC Output
R T ? DECR =
? 10.22
[k ? ] (1.5 – 12 V)
R T ? DECR =
? 15
[k ? ] (1.2 V)
R T ? DECR =
? 17
[k ? ] (1.0 V)
designer must, if necessary, decrease the maximum
current (originally obtained from the derating curves)
by the same percentage to ensure the converter’s
actual output power remains at or below the
maximum allowable output power.
Output Voltage Adjust /TRIM (Pin 6)
The output voltage can be adjusted up 10% or down
20% for Vout ≥ 1.5 V, and ± 10% for Vout = 1.2 V
relative to the rated output voltage by the addition of
an externally connected resistor. For output voltage
3.3 V, trim up to 10% is guaranteed only at
Vin ≥ 40 V, and it is marginal (8% to 10%) at
Vin = 36 V.
The TRIM pin should be left open if trimming is not
being used. To minimize noise pickup, a 0.1 μF
capacitor is connected internally between the TRIM
and SENSE(-) pins.
To increase the output voltage, refer to Fig. C. A trim
resistor, R T-INCR , should be connected between the
TRIM (Pin 6) and SENSE(+) (Pin 7), with a value of:
When trimming up, care must be taken not to exceed
the converter‘s maximum allowable output power. See
the previous section for a complete discussion of this
requirement.
To decrease the output voltage (Fig. D), a trim
resistor, R T-DECR , should be connected between the
TRIM (Pin 6) and SENSE(-) (Pin 5), with a value of:
511
Δ
700
Δ
700
| Δ |
where,
R T ? DECR = Required value of trim-down resistor [k ? ]
and Δ is defined above.
Note:
The above equations for calculation of trim resistor values match
those typically used in conventional industry-standard quarter-
R T ? INCR =
5.11(100 + Δ )V O ? NOM ? 626
1.225 Δ
for 1.5 – 12 V.
? 10.22
[k ? ],
bricks and one-eighth bricks (except for 1.2 V and 1.0 V outputs).
Converters with output voltages 1.2 V and 1.0 V are
available with alternative trim feature to provide the
customers with the flexibility of second sourcing.
? 7.2
? 9
R T ? INCR =
R T ? INCR =
84.6
Δ
120
Δ
[k ? ] (1.2 V)
[k ? ] (1.0 V)
These converters have a “T” character in the part
number. The trim equations of “T” version of
converters and more information can be found in
Application Note 103.
Semi Q Family
where,
R T ? INCR = Required value of trim-up resistor [k ? ]
V O ? NOM = Nominal value of output voltage [V]
Vin
Vin (+)
ON/OFF
TM
Converter
(Top View)
Vout (+)
SENSE (+)
TRIM
SENSE (-)
R T-DECR
Rload
Δ =
(V O - REQ ? V O - NOM )
V O - NOM
X 100 [%]
Vin (-) Vout (-)
Fig. D: Configuration for decreasing output voltage.
V O ? REQ = Desired (trimmed) output voltage [V].
Trimming/sensing beyond 110% of the rated output
voltage is not an acceptable design practice, as this
condition could cause unwanted triggering of the
Semi Q Family
Vin (+)
TM
Converter
Vout (+)
output overvoltage protection (OVP) circuit. The
designer should ensure that the difference between
Vin
ON/OFF
(Top View)
SENSE (+)
TRIM
R T-INCR
Rload
the voltages across the converter’s output pins and its
sense pins does not exceed 10% of V OUT ( NOM ), or:
SENSE (-)
[V OUT ( + ) ? V OUT ( ? )] ? [V SENSE ( + ) ? V SENSE ( ? )] ≤ V O - NOM X 10% [V]
Vin (-)
Vout (-)
This equation is applicable for any condition of output
Fig. C: Configuration for increasing output voltage.
sensing and/or output trim.
SEP 14, 2005 revised to NOV 06, 2006
Page 4 of 64
www.power-one.com
相关PDF资料
PDF描述
SQ48S15012-NS00 DC/DC EIGHTH BRICK
SQCSVA3R9CAT1A CAP CER 3.9PF 250V 0603
SQE48T10120-NDA0G DC/DC EIGHTH BRICK
SQE48T20050-NGB0 DC/DC EIGHTH BRICK
SQE48T20120-NDABG CONV DC-DC BUS 240W 12V 1/8 BRK
相关代理商/技术参数
参数描述
SQ48S03150-PS00G 制造商:Power-One 功能描述:Module DC-DC 1-OUT 15V 3.3A 8-Pin 1/8-Brick
SQ48S03150-PS0P 制造商:Power-One 功能描述:DCDC - Bulk
SQ48S03150-PS0PG 制造商:Power-One 功能描述:DCDC,HAZMAT - Bulk
SQ48S04120 制造商:Power-One 功能描述:- Bulk
SQ48S04120G 制造商:Power-One 功能描述:HAZMAT - Bulk