- 您现在的位置：买卖IC网 > Datasheet目录883 > SQ48S15012-NS00 (Power-One)DC/DC EIGHTH BRICK Datasheet资料下载
参数资料
| 型号： | SQ48S15012-NS00 |
| 厂商： | Power-One |
| 文件页数： | 6/64页 |
| 文件大小： | 0K |
| 描述： | DC/DC EIGHTH BRICK |
| 标准包装： | 24 |
| 系列： | * |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
SQ48 DC-DC Series Data Sheet
36-75 VDC Input; 1.0-12 VDC Output
Test Conditions
All data presented were taken with the converter
soldered to a test board, specifically a 0.060” thick
printed wiring board (PWB) with four layers. The top
and bottom layers were not metalized. The two inner
layers, comprised of two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that heat
transfer from the converter to the PWB was
minimized. This provides a worst-case but consistent
scenario for thermal derating purposes.
All measurements requiring airflow were made in the
vertical and horizontal wind tunnel using Infrared (IR)
thermography and thermocouples for thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining high
reliability. If one anticipates operating the converter
at or close to the maximum loads specified in the
derating curves, it is prudent to check actual
operating temperatures in the application.
Thermographic imaging is preferable; if this capability
is not available, then thermocouples may be used.
The use of AWG #40 gauge thermocouples is
recommended to ensure measurement accuracy.
Careful routing of the thermocouple leads will further
minimize measurement error. Refer to Fig. E for the
optimum measuring thermocouple location.
Fig. E: Location of the thermocouple for thermal testing.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Fig. x.1 to Fig. x.4 for through-hole
and surface-mount versions. Ambient temperature
was varied between 25°C and 85°C, with airflow
rates from 30 to 500LFM (0.15 to 2.5m/s), and
vertical and horizontal converter mounting.
For each set of conditions, the maximum load current
was defined as the lowest of:
(i) The output current at which any FET junction
temperature does not exceed a maximum specified
temperature (120°C) as indicated by the
thermographic image, or
(ii) The nominal rating of the converter (4A on 12V,
5.3A on 8.0V, 8A on 6.0V, 10A on 5.0V, and 15A on
3.3 – 1.0V).
During normal operation, derating curves with
maximum FET temperature less or equal to 120 °C
should not be exceeded. Temperature on the PCB at
thermocouple location shown in Fig. E should not
exceed 118 °C in order to operate inside the derating
curves.
Efficiency
Fig. x.5 shows the efficiency vs. load current plot for
ambient temperature of 25oC, airflow rate of 300 LFM
(1.5 m/s) with vertical mounting and input voltages of
36V, 48V and 72V. Also, a plot of efficiency vs. load
current, as a function of ambient temperature with
Vin = 48V, airflow rate of 200 LFM (1 m/s) with vertical
mounting is shown in Fig. x.6.
Power Dissipation
Fig. x.7 shows the power dissipation vs. load current
plot for Ta = 25oC, airflow rate of 300LFM (1.5 m/s)
with vertical mounting and input voltages of 36V, 48V
and 72V. Also, a plot of power dissipation vs. load
current, as a function of ambient temperature with
Vin = 48V, airflow rate of 200LFM (1 m/s) with vertical
mounting is shown in Fig. x.8.
Startup
Output voltage waveforms, during the turn-on
transient using the ON/OFF pin for full rated load
currents (resistive load) are shown without and with
external load capacitance in Fig. x.9 and Fig. x.10,
respectively.
Ripple and Noise
Fig. x.13 shows the output voltage ripple waveform,
measured at full rated load current with a 10 μF
tantalum and 1 μF ceramic capacitor across the
output. Note that all output voltage waveforms are
measured across a 1 μF ceramic capacitor.
The input reflected ripple current waveforms are
obtained using the test setup shown in Fig x.14. The
corresponding waveforms are shown in Fig. x.15 and
Fig. x.16.
Rev6 11-Apr-2011
Page 6 of 64
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| SQCSVA3R9CAT1A | CAP CER 3.9PF 250V 0603 |
| SQE48T10120-NDA0G | DC/DC EIGHTH BRICK |
| SQE48T20050-NGB0 | DC/DC EIGHTH BRICK |
| SQE48T20120-NDABG | CONV DC-DC BUS 240W 12V 1/8 BRK |
| SQE48T30012-NGB0 | DC/DC EIGHTH BRICK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SQ48S15012-NS00G | 制造商:Power-One 功能描述: |
| SQ48S15012-NS0P | 制造商:Power-One 功能描述:MOD DC-DC 1-OUT 1.2V 15A 50W 8PIN QUARTER-BRICK - Bulk |
| SQ48S15012-NS0PG | 制造商:Power-One 功能描述:MOD DC-DC 1-OUT 1.2V 15A 50W 8PIN QUARTER-BRICK - Bulk |
| SQ48S15012-PS00 | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQ48S15012-PS00G | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。