参数资料
| 型号： | SQ48T10050-NBB0 |
| 厂商： | Power-One |
| 文件页数： | 4/64页 |
| 文件大小： | 0K |
| 描述： | CONV DC-DC 48V IN 5V OUT 50W |
| 标准包装： | 24 |
| 系列： | SQ48 |
| 类型： | 隔离 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 36V |
| 电压 - 输入（最大）： | 75V |
| Voltage - Output 1： | 5V |
| 电流 - 输出（最大）： | 10A |
| 电源（瓦） - 制造商系列： | 50W |
| 电压 - 隔离： | 2kV（2000V） |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP 模块，1/4 砖 |
| 尺寸/尺寸： | 2.30" L x 0.90" W x 0.34" H（58.4mm x 22.9mm x 8.6mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 85°C |
| 电源（瓦特）- 最大： | 50W |
| 其它名称： | 179-2212 SQ48T10050-NAA0 SQ48T10050-NBBO |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
SQ48 DC-DC Series Data Sheet
36-75 VDC Input; 1.0-12 VDC Output
R T ? DECR =
? 10.22
[k ? ] (1.5 – 12 V)
R T ? DECR =
? 15
[k ? ] (1.2 V)
R T ? DECR =
? 17
[k ? ] (1.0 V)
designer must, if necessary, decrease the maximum
current (originally obtained from the derating curves)
by the same percentage to ensure the converter’s
actual output power remains at or below the
maximum allowable output power.
Output Voltage Adjust /TRIM (Pin 6)
The output voltage can be adjusted up 10% or down
20% for Vout ≥ 1.5 V, and ± 10% for Vout = 1.2 V
relative to the rated output voltage by the addition of
an externally connected resistor. For output voltage
3.3 V, trim up to 10% is guaranteed only at
Vin ≥ 40 V, and it is marginal (8% to 10%) at
Vin = 36 V.
The TRIM pin should be left open if trimming is not
being used. To minimize noise pickup, a 0.1 μF
capacitor is connected internally between the TRIM
and SENSE(-) pins.
To increase the output voltage, refer to Fig. C. A trim
resistor, R T-INCR , should be connected between the
TRIM (Pin 6) and SENSE(+) (Pin 7), with a value of:
When trimming up, care must be taken not to exceed
the converter‘s maximum allowable output power. See
the previous section for a complete discussion of this
requirement.
To decrease the output voltage (Fig. D), a trim
resistor, R T-DECR , should be connected between the
TRIM (Pin 6) and SENSE(-) (Pin 5), with a value of:
511
Δ
700
Δ
700
| Δ |
where,
R T ? DECR = Required value of trim-down resistor [k ? ]
and Δ is defined above.
Note:
The above equations for calculation of trim resistor values match
those typically used in conventional industry-standard quarter-
R T ? INCR =
5.11(100 + Δ )V O ? NOM ? 626
1.225 Δ
for 1.5 – 12 V.
? 10.22
[k ? ],
bricks and one-eighth bricks (except for 1.2 V and 1.0 V outputs).
Converters with output voltages 1.2 V and 1.0 V are
available with alternative trim feature to provide the
customers with the flexibility of second sourcing.
? 7.2
? 9
R T ? INCR =
R T ? INCR =
84.6
Δ
120
Δ
[k ? ] (1.2 V)
[k ? ] (1.0 V)
These converters have a “T” character in the part
number. The trim equations of “T” version of
converters and more information can be found in
Application Note 103.
Semi Q Family
where,
R T ? INCR = Required value of trim-up resistor [k ? ]
V O ? NOM = Nominal value of output voltage [V]
Vin
Vin (+)
ON/OFF
TM
Converter
(Top View)
Vout (+)
SENSE (+)
TRIM
SENSE (-)
R T-DECR
Rload
Δ =
(V O - REQ ? V O - NOM )
V O - NOM
X 100 [%]
Vin (-) Vout (-)
Fig. D: Configuration for decreasing output voltage.
V O ? REQ = Desired (trimmed) output voltage [V].
Trimming/sensing beyond 110% of the rated output
voltage is not an acceptable design practice, as this
condition could cause unwanted triggering of the
Semi Q Family
Vin (+)
TM
Converter
Vout (+)
output overvoltage protection (OVP) circuit. The
designer should ensure that the difference between
Vin
ON/OFF
(Top View)
SENSE (+)
TRIM
R T-INCR
Rload
the voltages across the converter’s output pins and its
sense pins does not exceed 10% of V OUT ( NOM ), or:
SENSE (-)
[V OUT ( + ) ? V OUT ( ? )] ? [V SENSE ( + ) ? V SENSE ( ? )] ≤ V O - NOM X 10% [V]
Vin (-)
Vout (-)
This equation is applicable for any condition of output
Fig. C: Configuration for increasing output voltage.
sensing and/or output trim.
SEP 14, 2005 revised to NOV 06, 2006
Page 4 of 64
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| SY100E431JZ TR | IC FLIP FLOP 3BIT DIFF 28-PLCC |
| RNS03ZE-M6 | CONV DC-DC 48V IN 3.3V OUT 10W |
| SY100E431JZ | IC FLIP FLOP 3BIT DIFF 28-PLCC |
| SY55852UKI | IC FLIP FLOP D 2.5GHZ 10-MSOP |
| SY55852UKC | IC FLIP FLOP D 2.5GHZ 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SQ48T10050-NBB0A | 制造商:Power-One 功能描述: |
| SQ48T10050-NBB0G | 功能描述:DC/DC转换器 36-75Vin 10A 5.0Vout 50W RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQ48T10050-NBBO | 制造商:POWER-ONE INC 功能描述:PwrSup;DC-DC Converter;Out 5VDC;In 36 to 75VDC;Thru-Hole;Open-Frame;Switching;1 |
| SQ48T10050-NBC0 | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQ48T10050-NBC0G | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。