- 您现在的位置：买卖IC网 > Datasheet目录883 > SQE48T10120-NDA0G (Power-One)DC/DC EIGHTH BRICK Datasheet资料下载
参数资料
| 型号： | SQE48T10120-NDA0G |
| 厂商： | Power-One |
| 文件页数： | 5/13页 |
| 文件大小： | 0K |
| 描述： | DC/DC EIGHTH BRICK |
| 标准包装： | 50 |
| 系列： | * |
SQE48T10120 DC-DC Converter
36-75 VDC Input; 12 VDC @ 10A Output
Data Sheet
Operations
Input and Output Impedance
These power converters have been designed to be
stable with no external capacitors when used in low
inductance input and output circuits.
However, in some applications, the inductance
associated with the distribution from the power
source to the input of the converter can affect the
See the Startup Information section for system timing
waveforms associated with use of the ON/OFF pin.
Remote Sense (Pins 5 and 7)
The remote sense feature of the converter
compensates for voltage drops occurring between
the output pins of the converter and the load. The
SENSE(-) (Pin 5) and SENSE(+) (Pin 7) pins should
be connected at the load or at the point where
regulation is required (see Figure B).
stability of the converter. A 33 μF electrolytic
capacitor with an ESR < 1 ? across the input is
recommended to ensure stability of the converter.
Vin (+)
SQE48 Converter
(Top View)
Vout (+)
100
Rw
In many applications, the user has to use decoupling
capacitance at the load. The power converter will
exhibit stable operation with external load
capacitance up to 5,000 μF.
Vin
ON/OFF
Vin (-)
SENSE (+)
TRIM
SENSE (-)
10
Vout (-)
Rw
Rload
ON/OFF (Pin 2)
The ON/OFF pin is used to turn the power converter
on or off remotely via a system signal. There are two
remote control options available, positive and
negative logic, with both referenced to Vin(-). A
typical connection is shown in Figure A.
Fig. B: Remote sense circuit configuration.
CAUTION
If remote sensing is not utilized, the SENSE(-) pin must be
connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin
must be connected to the Vout(+) pin (Pin 8) to ensure the
converter will regulate at the specified output voltage. If these
connections are not made, the converter will deliver an
Vin (+)
SQE48 Converter
Vout (+)
output voltage that is higher than the specified data sheet
value.
Vin
ON/OFF
(Top View)
SENSE (+)
TRIM
Rload
Because the sense leads carry minimal current,
large traces on the end-user board are not required.
SENSE (-)
However, sense traces should be run side by side
CONTROL
INPUT
Vin (-)
Vout (-)
and located close to a ground plane to minimize
system noise and ensure optimum performance.
Fig. A: Circuit configuration for ON/OFF function.
The positive logic version turns on when the ON/OFF
pin is at a logic high and turns off when at a logic
low. The converter is on when the ON/OFF pin is left
open. See the Electrical Specifications for logic
high/low definitions.
The negative logic version turns on when the pin is
at a logic low and turns off when the pin is at a logic
high. The ON/OFF pin can be hard wired directly to
Vin(-) to enable automatic power up of the converter
without the need of an external control signal.
The ON/OFF pin is internally pulled up to 5V through
a resistor. A properly de-bounced mechanical switch,
open-collector transistor, or FET can be used to
drive the input of the ON/OFF pin. The device must
be capable of sinking up to 0.2 mA at a low level
voltage of ≤ 0.8 V. An external voltage source (±20 V
maximum) may be connected directly to the ON/OFF
input, in which case it must be capable of sourcing or
sinking up to 1 mA depending on the signal polarity.
The converter’s output overvoltage protection (OVP)
senses the voltage across Vout(+) and Vout(-), and
not across the sense lines, so the resistance (and
resulting voltage drop) between the output pins of
the converter and the load should be minimized to
prevent unwanted triggering of the OVP.
When utilizing the remote sense feature, care must
be taken not to exceed the maximum allowable
output power capability of the converter, which is
equal to the product of the nominal output voltage
and the allowable output current for the given
conditions.
When using remote sense, the output voltage at the
converter can be increased by as much as 10%
above the nominal rating in order to maintain the
required voltage across the load. Therefore, the
designer must, if necessary, decrease the maximum
current (originally obtained from the derating curves)
by the same percentage to ensure the converter’s
ZD-02075 Rev 1.1, 21-Jan-10
www.power-one.com
Page 5 of 13
相关PDF资料 |
PDF描述 |
|---|---|
| SQE48T20050-NGB0 | DC/DC EIGHTH BRICK |
| SQE48T20120-NDABG | CONV DC-DC BUS 240W 12V 1/8 BRK |
| SQE48T30012-NGB0 | DC/DC EIGHTH BRICK |
| SQE48T40015-NDA0 | DC/DC EIGHTH BRICK |
| SQE48T40018-NDA0 | DC/DC EIGHTH BRICK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SQE48T10120-NDB0G | 制造商:Power-One 功能描述:Conn Subminiature Cylindrical PIN 15 POS Crimp ST Wall Mount 15 Terminal 1 Port 制造商:Power-One 功能描述:- Bulk |
| SQE48T10120-PDA0G | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQE48T20033－NGB0G | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 20A 8PIN - Bulk 制造商:Power-One 功能描述:Module DC-DC 1-OUT 3.3V 20A 8-Pin 1/8-Brick 制造商:Power-One 功能描述:DC/DC CONVERTER 3.3V 66W |
| SQE48T20033-NGBO | 制造商:POWER-ONE INC 功能描述:PwrSup;DC-DC Converter;Out 3.3VDC;In 36 to 75VDC;Thru-Hole;Open-Frame;Switching |
| SQE48T20050-NDAK | 制造商:Power-One 功能描述:SQE48T Series Single Output 5 V DC/DC Converter Power Supply |
发布紧急采购，3分钟左右您将得到回复。