参数资料
| 型号： | SRDA05-4R2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 5/8页 |
| 文件大小： | 0K |
| 描述： | TVS ARRAY LO CAP 500W 8SOIC |
| 产品变化通告： | Product Discontinuation 27/Jun/2007 |
| 标准包装： | 2,500 |
| 电压 - 反向隔离（标准值）： | 5V |
| 电压 - 击穿： | 6V |
| 功率（瓦特）： | 500W |
| 电极标记： | 4 通道阵列 - 单向 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
| 其它名称： | SRDA05-4R2OS |
SRDA05-4R2
ESD Protection of Power Supply Lines
When using diodes for data line protection, referencing to
a supply rail provides advantages. Biasing the diodes reduces
their capacitance and minimizes signal distortion.
Implementing this topology with discrete devices does have
disadvantages. This configuration is shown below:
L di ESD /dt factor. A relatively small trace inductance can result
in hundreds of volts appearing on the supply rail. This
endangers both the power supply and anything attached to
that rail. This highlights the importance of good board layout.
Taking care to minimize the effects of parasitic inductance
will provide significant benefits in transient immunity.
Even with good board layout, some disadvantages are still
Power
Supply
V CC
I ESDpos
present when discrete diodes are used to suppress ESD events
across datalines and the supply rail. Discrete diodes with good
transient power capability will have larger die and therefore
Protected Data Line
Device
D1
D2
I ESDpos
I ESDneg
VF + V CC
I ESDneg
higher capacitance. This capacitance becomes problematic as
transmission frequencies increase. Reducing capacitance
generally requires reducing die size. These small die will have
higher forward voltage characteristics at typical ESD
transient current levels. This voltage combined with the
smaller die can result in device failure.
-VF
Figure 8.
Looking at the figure above, it can be seen that when a
positive ESD condition occurs, diode D1 will be forward
The ON Semiconductor SRDA05- 4R2 was developed to
overcome the disadvantages encountered when using discrete
diodes for ESD protection. This device integrates a TVS
diode within a network of steering diodes.
biased while diode D2 will be forward biased when a negative
D1
D3
D5
D7
ESD condition occurs. For slower transient conditions, this
system may be approximated as follows:
For positive pulse conditions:
Vc = Vcc + Vf D1
D2
D4
D6
D8
For negative pulse conditions:
Vc = -Vf D2
ESD events can have rise times on the order of some
number of nanoseconds. Under these conditions, the effect of
parasitic inductance must be considered. A pictorial
representation of this is shown below.
Power
0
Figure 10. SRDA05-4R2 Equivalent Circuit
During an ESD condition, the ESD current will be driven
to ground through the TVS diode as shown below.
Supply
V CC
I ESDpos
Power
Supply
Protected
Device
Data Line
D1
I ESDpos
I ESDneg
V CC
D1
I ESDpos
D2
V C = V CC + Vf + (L diESD/dt)
I ESDneg
Protected
Device
Data Line
D2
V C = -Vf - (L diESD/dt)
Figure 9.
An approximation of the clamping voltage for these fast
transients would be:
For positive pulse conditions:
Vc = Vcc + Vf + (L di ESD /dt)
For negative pulse conditions:
Vc = -Vf – (L di ESD /dt)
As shown in the formulas, the clamping voltage (Vc) not
only depends on the Vf of the steering diodes but also on the
Figure 11.
The resulting clamping voltage on the protected IC will
be:
Vc = V FD1 + V TVS .
The clamping voltage of the TVS diode is provided in
Figure 4 and depends on the magnitude of the ESD current.
The steering diodes are fast switching devices with unique
forward voltage and low capacitance characteristics.
http://onsemi.com
5
相关PDF资料 |
PDF描述 |
|---|---|
| MMA21-020 | CONN RACK/PANEL 20POS 5A |
| 1SMA16CAT3 | TVS 400W 16V BIDIRECT SMA |
| OP482GP | IC OPAMP JFET 4MHZ QUAD LP 14DIP |
| 1SMF16BT3 | TVS ZENER 175W 16V SOD123FL |
| 1PMT16AT3G | TVS 200W 16V POWERMITE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SRDA05-4R2/D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Low Capacitance Surface Mount TVS for High-Speed Data Interfaces |
| SRDA05-4R2G | 功能描述:TVS二极管阵列 LO CAPACITANCE SURF MNT TVS RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C |
| SRDA05-4T | 制造商:Semtech Corporation 功能描述:ESD Suppressor Diode Arrays 制造商:Semtech Corporation 功能描述:TVS Diode |
| SRDA05-4TB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:RailClamp Low Capacitance TVS Diode Array |
| SRDA054TBT | 制造商:Semtech Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。