- 您现在的位置：买卖IC网 > PDF目录18918 > SS-01D-12 (Omron Electronics Inc-EMC Div)SWITCH SNAP STR SPST .1A 150G PDF资料下载
参数资料
| 型号： | SS-01D-12 |
| 厂商： | Omron Electronics Inc-EMC Div |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | SWITCH SNAP STR SPST .1A 150G |
| 标准包装： | 500 |
| 系列： | * |
| 其它名称： | SS01D12 |
Precautions
Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide,
“Snap Action Switches, Technical Information” for correct use.
■ Correct Use
Mounting
Mount the switch onto a flat surface. Mounting on an uneven surface
may cause deformation of the switch, resulting in faulty operation or
breakage in the housing.
Operating Stroke
Take particular care in setting the operating stroke for the pin plunger
models. Make sure that the operating stroke is 70% to 100% of the
rated OT distance. Do not operate the actuator exceeding the OT dis-
tance, otherwise the life expectancy of the switch may be shortened.
Using Microloads
Using a model for ordinary loads to switch microloads may result in
faulty operation. Instead, use the models that are designed for
microloads and that operate in the following range;
■ Cautions
Handling
Turn OFF the power supply before mounting or removing the switch,
wiring, or performing maintenance for inspection. Failure to do so
may result in electric shock or burning
Terminal Connection
When soldering the lead wire to the terminal, first insert the lead wire
conductor through the terminal hole and then solder.
Make sure that the capacity of the soldering iron is 60 W maximum.
Do not take more than 5 seconds to solder the switch terminal.
Improper soldering involving an excessively high temperature or
excessive soldering time may deteriorate the characteristics of the
switch.
Be sure to apply only the minimum required amount of flux. The
switch may have contact failures if flux intrudes in the interior of the
switch.
Use the following lead wires to connect to the solder terminals;
30
0.16mA
26mA 100mA
Model
Conductor size
SS-5
0.5 to 0.75 mm 2
24
SS-10
0.75 mm 2
Operating range
for micro load
models SS-01
Operating
range for
general-load
models
If the PCB terminal models are soldered in a solder bath, flux will per-
meate inside the switch and cause contact failure. Therefore, manu-
ally solder the PCB terminal.
12
5
Inopera b le
range
1mA
SS-5, SS-10
100mA 160mA
Wire the quick-connect terminals (#110) with receptacles. Insert the
terminals straight into the receptacles. Do not impose excessive
force on the terminal in the horizontal direction, otherwise the termi-
nal may be deformed or the housing may be damaged.
Insulation Distance
0
1
10
100
1,000
Use a separator between the switch and metal mounting panels, to
C u rrent (mA)
However, even when using microload models within the operating
range shown above, if inrush current or inductive voltage spikes
occur when the contact is opened or closed, then contact wear may
increase and so decrease the service life. Therefore, insert a contact
protection circuit where necessary.
ensure proper dielectric characteristics are achieved.
According to E N 61058-1, the minimum insulation thickness for this
switch should be 1.1 mm and minimum clearance distance between
the terminal and mounting plate should be 1.6 mm. If the insulation
distance cannot be provided in the product incorporating the switch,
either use a switch with insulation barrier or use a separator to
ensure sufficient insulation distance.
Separator
Snap Action Switch
SS
101
相关PDF资料 |
PDF描述 |
|---|---|
| Q19P1CXXY110E | INDICATOR 110V 19MM PROM YELLOW |
| Q19P1CXXG110E | INDICATOR 110V 19MM PROM GREEN |
| ASFLMB-125.000MHZ-LY-T | OSC MEMS 125.000 MHZ SMD |
| Q19P1CXXR110E | INDICATOR 110V 19MM PROM RED |
| ASFLMB-14.7456MHZ-XY-T | OSC MEMS 14.7456 MHZ SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SS01D2 | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT PIN PLUNGER PC PINS 0.1A 125VAC 30VDC 1.4 - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH BASIC SPDT .1A PCB 制造商:Omron Electronic Components LLC 功能描述:Switch Snap Action N.O./N.C. SPDT Pin Plunger PC Pins 0.1A 125VAC 30VDC 1.47N Thru-Hole |
| SS-01D2 | 功能描述:基本/快动开关 SPDT 0.1A 125VAC 30VDC Sw Snap Action RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| SS01E | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT PIN PLUNGER SLDR 0.1A 125VAC 30VDC 0.25N - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH BASIC SPDT .1A 制造商:Omron Electronic Components LLC 功能描述:Switch Snap Action N.O./N.C. SPDT Pin Plunger Solder 0.1A 125VAC 30VDC 0.25N Screw Mount |
| SS-01-E | 功能描述:基本/快动开关 Subminiature Basic Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| SS01E3D2 | 制造商:Omron Electronic Components LLC 功能描述:SUBMINIATURE BASIC SWITCH - Trays 制造商:Omron Electronic Components LLC 功能描述:SW SUBMINI SPST-NO .1A PIN PLNGR 制造商:Omron Electronic Components LLC 功能描述:Switch Snap Action N.O. SPST Pin Plunger PC Pins 0.1A 125VAC 30VDC 0.25N Thru-Hole |
发布紧急采购，3分钟左右您将得到回复。