- 您现在的位置：买卖IC网 > PDF目录21954 > SS-3GLPT (Omron Electronics Inc-EMC Div)SWITCH LEVER SPDT 3A .110QC PDF资料下载
参数资料
| 型号： | SS-3GLPT |
| 厂商： | Omron Electronics Inc-EMC Div |
| 文件页数： | 5/6页 |
| 文件大小： | 0K |
| 描述： | SWITCH LEVER SPDT 3A .110QC |
| 产品培训模块： | Snap Switches Medical Solutions |
| 产品目录绘图： | SS, SS-P Series SS-Quick Connect_14.5-straight |
| 标准包装： | 100 |
| 系列： | SS |
| 电路： | 单刀双掷 |
| 开关功能： | 开-瞬时 |
| 触点额定电压： | 3A @ 125VAC |
| 触动器类型： | 按片，直形 |
| 安装类型： | 底座安装 |
| 端接类型： | 快速连接 - 0.110"（2.8mm） |
| 操作力： | 50gf |
| 产品目录页面： | 2538 (CN2011-ZH PDF) |
| 其它名称： | SS3GLPT SW767 |
Precautions
■ Correct Use
Mounting
Mount the Switch onto a flat surface. Mounting on an uneven surface
may cause deformation of the Switch, resulting in faulty operation or
breakage in the housing.
Operating Stroke Setting
Take particular care in setting the operating stroke for the pin plunger
models. Make sure that the operating stroke is 60% to 90% of the
rated OT distance. Do not operate the actuator exceeding the OT dis-
tance, otherwise the life expectancy of the Switch may be shortened.
Using Microloads
Using a model for ordinary loads to switch microloads may result in
faulty operation. Instead, use the models that are designed for micro-
loads and that operate in the following range;
■ Cautions
Handling
Turn OFF the power supply before mounting or removing the Switch,
wiring, or performing maintenance or inspection. Failure to do so may
result in electric shock or burning.
Solder Terminal Connection
When soldering lead wires to solder terminals, first insert the lead
wire conductor through the terminal hole and then solder.
Make sure that the temperature at the tip of the soldering iron is
350 to 400 ° C. Do not take more than 3 seconds to solder the switch
terminal, and do not impose external force on the terminal for 1 min
after soldering. Improper soldering involving an excessively high
temperature or excessive soldering time may deteriorate the charac-
teristics of the Switch.
Quick-Connect Terminals
Wire quick-connect terminals (#110) with receptacles. Insert the ter-
30
0.16 mA
26 mA
1 00 mA
minals straight into the receptacles. Do not impose excessive force
on the terminal in the horizontal direction, otherwise the terminal may
be deformed or the housing may be damaged.
24
Use appropriate #110 QC connectors, made by N ippon Tanshi or
12
Operatin g ran g e
for micro load
models SS-01P
Operatin g
ran g e for
g eneral-
load models
SS-3P
Tyco Electronics, to mate with the quick-connect versions of the
switch. These connectors are not sold by OMRO N . Contact N ippon
Tanshi or Tyco Electronics to purchase these connectors.
PCB Terminal Connection
5
Inoperable
ran g e
1 mA
100 mA 16 0 mA
When using automatic soldering baths, we recommend soldering at
260 ± 5 ° C within 5 seconds. Make sure that the liquid surface of the
solder does not flow over the edge of the board.
0
0.1 1 10 100 1,000
Current (mA)
However, even when using microload models within the operating
range shown above, if inrush current or inductive voltage spikes
occur when the contact is opened or closed, it may increase contact
wear and so decrease the service life. Therefore, insert a contact
protection circuit where necessary.
When soldering by hand, as a guideline, solder with a soldering iron
with a tip temperature of 350 to 400 ° C within 3 seconds, and do not
apply any external force for at least 1 minutes after soldering. When
applying solder, keep the solder away from the case of the Switch
and do not allow solder or flux to enter the case.
Insulation Distance
Use a separator between the switch and metal mounting panels, to
ensure proper dielectric characteristics are achieved.
Subminiature Basic Switch
SS-P
107
相关PDF资料 |
PDF描述 |
|---|---|
| IR2166PBF | IC CONTROLLER PFC/BALLAST 16DIP |
| DBM13W3S500CN | CONN DSUB RCPT 13W3 T/H RA GOLD |
| CWX813-014.31818M | OSC 14.31818MHZ 3.3V +-25PPM SMD |
| SS-01GL13P | SWITCH SIM ROLLER SPDT .1A SLDR |
| SS-3GL13PT | SWITCH SIM ROLLER SPDT 3A .110QC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SS3GP | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT PIN PLUNGER SLDR 3A 125VAC 30VDC 1.5N TH - Trays |
| SS-3GP | 功能描述:基本/快动开关 3A Pin Plunger Solder terminals RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| SS3GPB | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT PIN PLUNGER PC PINS 3A 125VAC 30VDC 1.5N - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH BASIC SPDT 3A PCB |
| SS-3GPB | 功能描述:基本/快动开关 3A Pin plunger PCB terminals even RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel |
| SS3GPD | 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT PIN PLUNGER PC PINS 3A 125VAC 30VDC 1.5N - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH BASIC SPDT 3A PCB |
发布紧急采购，3分钟左右您将得到回复。