参数资料
| 型号： | ST16C2550CJ44-F |
| 厂商： | Exar Corporation |
| 文件页数： | 11/37页 |
| 文件大小： | 0K |
| 描述： | IC DUART FIFO 16B 44PLCC |
| 标准包装： | 27 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 管件 |
| 其它名称： | 1016-1254-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
ST16C2550
19
REV. 4.4.1
2.97V TO 5.5V DUART WITH 16-BYTE FIFO
4.4
Interrupt Status Register (ISR) - Read-Only
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with four interrupt status bits. Performing a read cycle on the
ISR will give the user the current highest pending interrupt level to be serviced, others are queued up to be
serviced next. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt
Source Table, Table 8, shows the data values (bits 0-3) for the interrupt priority levels and the interrupt sources
associated with each of these interrupt levels.
4.4.1
Interrupt Generation:
LSR is by any of the LSR bits 1, 2, 3 and 4.
RXRDY is by RX trigger level.
RXRDY Time-out is by a 4-char plus 12 bits delay timer.
TXRDY is by TX FIFO empty.
MSR is by any of the MSR bits 0, 1, 2 and 3.
4.4.2
Interrupt Clearing:
LSR interrupt is cleared by a read to the LSR register.
RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level.
RXRDY Time-out interrupt is cleared by reading RHR.
TXRDY interrupt is cleared by a read to the ISR register or writing to THR.
MSR interrupt is cleared by a read to the MSR register.
]
TABLE 8: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY LEVEL
ISR REGISTER STATUS BITS
SOURCE OF INTERRUPT
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
0
LSR (Receiver Line Status Register)
2
1
0
RXRDY (Receive Data Time-out)
3
0
1
0
RXRDY (Received Data Ready)
4
0
1
0
TXRDY (Transmit Ready)
5
0
MSR (Modem Status Register)
-
0
1
None (default)
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default).
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Table 8).
ISR[5:4]: Reserved
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
相关PDF资料 |
PDF描述 |
|---|---|
| ST16C2552IJ44TR-F | IC UART FIFO 16B DUAL 44PLCC |
| ST16C450CJ44-F | IC UART SINGLE 44PLCC |
| ST16C450CP40-F | IC INTERFACE UART |
| ST16C452IJ68-F | IC UART W/PAR PORT DUAL 68PLCC |
| ST16C454IJ68TR-F | IC UART QUAD 68PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C2550CJ44TR-F | 功能描述:UART 接口集成电路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CP40 | 功能描述:UART 接口集成电路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CP40-F | 功能描述:UART 接口集成电路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CQ-0A-EB | 功能描述:界面开发工具 EVAL SYSTEM RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| ST16C2550CQ-0B-EB | 功能描述:界面开发工具 Supports C2550 48 ld TQFP, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。