参数资料
型号: ST16C2550IJ44-F
厂商: Exar Corporation
文件页数: 5/37页
文件大小: 0K
描述: IC UART FIFO 16B DUAL 44PLCC
标准包装: 27
特点: *
通道数: 2,DUART
FIFO's: 16 字节
规程: RS232,RS485
电源电压: 2.97 V ~ 5.5 V
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 44-LCC(J 形引线)
供应商设备封装: 44-PLCC(16.59x16.59)
包装: 管件
其它名称: 1016-1562-5
ST16C2550IJ44-F-ND
FIGURE 7. TRANSMITTER OPERATION IN NON-FIFO MODE
Transmit
Holding
Register
(THR)
Transmit Shift Register (TSR)
Data
Byte
L
S
B
M
S
B
THR Interrupt (ISR bit-1)
Enabled by IER bit-1
TXNOFIFO1
16X Clock
ST16C2550
13
REV. 4.4.1
2.97V TO 5.5V DUART WITH 16-BYTE FIFO
2.9.3
Transmitter Operation in FIFO Mode
The host may fill the transmit FIFO with up to 16 bytes of transmit data. The THR empty flag (LSR bit-5) is set
whenever the FIFO is empty. The THR empty flag can generate a transmit empty interrupt (ISR bit-1) when the
FIFO becomes empty. The transmit empty interrupt is enabled by IER bit-1. The TSR flag (LSR bit-6) is set
when TSR/FIFO becomes empty.
FIGURE 8. TRANSMITTER OPERATION IN FIFO MODE
Transmit Data Shift Register
(TSR)
Data Byte
THR Interrupt (ISR bit-1) when TX
FIFO becomes empty. FIFO is
enabled by FCR bit-0=1.
Transmit FIFO
16X Clock
TXFIFO1
THR
2.10
Receiver
The receiver section contains an 8-bit Receive Shift Register (RSR) and 16 bytes of FIFO which includes a
byte-wide Receive Holding Register (RHR). The RSR uses the 16X clock for timing. It verifies and validates
every bit on the incoming character in the middle of each data bit. On the falling edge of a start or false start bit,
an internal receiver counter starts counting at the 16X clock rate. After 8 clocks the start bit period should be at
the center of the start bit. At this time the start bit is sampled and if it is still a logic 0 it is validated. Evaluating
the start bit in this manner prevents the receiver from assembling a false character. The rest of the data bits
and stop bits are sampled and validated in this same manner to prevent false framing. If there were any
error(s), they are reported in the LSR register bits 2-4. Upon unloading the receive data byte from RHR, the
receive FIFO pointer is bumped and the error tags are immediately updated to reflect the status of the data
byte in RHR register. RHR can generate a receive data ready interrupt upon receiving a character or delay until
it reaches the FIFO trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready
time-out interrupt when data is not received for 4 word lengths as defined by LCR[1:0] plus 12 bits time. This is
equivalent to 3.7-4.6 character times. The RHR interrupt is enabled by IER bit-0.
相关PDF资料
PDF描述
VI-JWJ-IW-F2 CONVERTER MOD DC/DC 36V 100W
VI-JWJ-IW-F1 CONVERTER MOD DC/DC 36V 100W
VI-JWH-IW-F4 CONVERTER MOD DC/DC 52V 100W
XR68C92IV-F DUAL CHANNEL UART 44LQFP
MS27479E10C35P CONN RCPT 13POS WALL MNT W/PINS
相关代理商/技术参数
参数描述
ST16C2550IJ44TR-F 制造商:Exar Corporation 功能描述:UART 2-CH 16Byte FIFO 3.3V/5V 44-Pin PLCC T/R 制造商:Exar Corporation 功能描述:ST16C2550IJ44TR-F
ST16C2550IP40 功能描述:UART 接口集成电路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
ST16C2550IQ48 制造商:Rochester Electronics LLC 功能描述:
ST16C2550IQ48-F 功能描述:UART 接口集成电路 2.97V-5.5V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
ST16C2550IQ48TR-F 功能描述:UART 接口集成电路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel