- 您现在的位置：买卖IC网 > PDF目录11832 > ST16C554CQ64-F (Exar Corporation)IC UART FIFO 16B QUAD 64LQFP PDF资料下载
参数资料
| 型号： | ST16C554CQ64-F |
| 厂商： | Exar Corporation |
| 文件页数： | 11/39页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B QUAD 64LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 16 字节 |
| 规程： | RS232 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 其它名称： | 1016-1264 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
ST16C554/554D
19
REV. 4.0.1
2.97V TO 5.5V QUAD UART WITH 16-BYTE FIFO
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger levels, and select the
DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default).
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Reserved (Default 0)
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 10 shows the complete selections.
TABLE 10: RECEIVE FIFO TRIGGER LEVEL SELECTION
FCR BIT-7
FCR BIT-6
RECEIVE TRIGGER LEVEL
0
1
0
1
0
1
4
8
14
相关PDF资料 |
PDF描述 |
|---|---|
| VE-26P-IY | CONVERTER MOD DC/DC 13.8V 50W |
| XR17D152CMTR-F | IC UART PCI BUS DUAL 100TQFP |
| VE-26J-IY | CONVERTER MOD DC/DC 36V 50W |
| MS27472E14B18P | CONN RCPT 18POS WALL MT W/PINS |
| VE-26F-IY | CONVERTER MOD DC/DC 72V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C554D | 制造商:EXAR 制造商全称:EXAR 功能描述:QUAD UART WITH 16-BYTE FIFOS |
| ST16C554DCJ | 制造商:Exar Corporation 功能描述: |
| ST16C554DCJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: 制造商:Exar Corporation 功能描述:IC,UART,LDCC,68PIN,PLASTIC |
| ST16C554DCJ-68 | 制造商:Exar Corporation 功能描述:IC,UART,LDCC,68PIN,PLASTIC |
| ST16C554DCJ68-F | 功能描述:UART 接口集成电路 2.97V-5.5V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。