参数资料
| 型号： | ST16C654CQ64-F |
| 厂商： | Exar Corporation |
| 文件页数： | 25/51页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B QUAD 64LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 64 字节 |
| 规程： | RS232 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 其它名称： | 1016-1445 ST16C654CQ64-F-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
xr
ST16C654/654D
REV. 5.0.2
2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
31
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be set to a logic zero during 68 mode.
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During loopback mode, it sets
OP2# internally to a logic 1.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During loopback mode, it sets OP2# internally
to a logic 0.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 13.
MCR[5]: Xon-Any Enable
Logic 0 = Disable Xon-Any function (for 16C550 compatibility, default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO , unless the RX character is an Xon or Xoff character and
the 654 is programmed to use the Xon/Xoff flow control.
MCR[6]: Infrared Encoder/Decoder Enable
Logic 0 = Enable the standard modem receive and transmit input/output interface. (Default)
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. The TX/RX output/input are routed to the
infrared encoder/decoder. The data input and output levels conform to the IrDA infrared interface
requirement. The RX FIFO may need to be flushed upon enable. While in this mode, the infrared TX output
will be a logic 0 during idle data conditions.
MCR[7]: Clock Prescaler Select
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
4.8
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host. If IER bit-2 is enabled, LSR
bit 1 will generate an interrupt immediately and LSR bits 2-4 will generate an interrupt when a character with an
error is in the RHR.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
TABLE 14: INT OUTPUT MODES
INTSEL
PIN
MCR
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
Three-State
0
1
Active
1
X
Active
相关PDF资料 |
PDF描述 |
|---|---|
| ST16C654DCQ64-F | IC UART FIFO 64B QUAD 64LQFP |
| ST16C654IQ100-F | IC UART FIFO 64B QUAD 100QFP |
| XR16V654IL-F | IC UART FIFO 64B QUAD 48QFN |
| XR16C2850CM-F | IC UART FIFO 128B DUAL 48TQFP |
| ST16C554DIQ64-F | IC UART FIFO 16B QUAD 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C654CQ64TR-F | 功能描述:UART 接口集成电路 QUAD UARTW/64BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C654D | 制造商:EXAR 制造商全称:EXAR 功能描述:2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO |
| ST16C654DCQ64 | 制造商:Exar Corporation 功能描述: |
| ST16C654DCQ64-0A-EB | 功能描述:界面开发工具 Supports C654D 64 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| ST16C654DCQ64-F | 功能描述:UART 接口集成电路 QUAD UARTW/64BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。