参数资料
型号: ST6200CM6/XXX
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO16
封装: 0.300 INCH, ROHS COMPLIANT, PLASTIC, SOP-16
文件页数: 56/100页
文件大小: 3849K
代理商: ST6200CM6/XXX
ST6200C ST6201C ST6203C
Doc ID 4563 Rev 5
59/100
10.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maxi-
mum ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device under these condi-
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
10.2.1 Voltage Characteristics
10.2.2 Current Characteristics
10.2.3 Thermal Characteristics
Notes:
1. Directly connecting the RESET and I/O pins to VDD or VSS could damage the device if an unintentional internal reset
is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program coun-
ter). To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7k
Ω
for RESET, 10k
Ω for I/Os). Unused I/O pins must be tied in the same way to VDD or VSS according to their reset con-
figuration.
2. When the current limitation is not possible, the VIN absolute maximum rating must be respected, otherwise refer to
IINJ(PIN) specification. A positive injection is induced by VIN>VDD while a negative injection is induced by VIN<VSS.
3. Power (VDD) and ground (VSS) lines must always be connected to the external supply.
4. Negative injection disturbs the analog performance of the device. In particular, it induces leakage currents throughout
the device including the analog inputs. To avoid undesirable effects on the analog functions, care must be taken:
- Analog input pins must have a negative injection less than 1mA (assuming that the impedance of the analog voltage
is lower than the specified limits).
- Pure digital pins must have a negative injection less than 1mA. In addition, it is recommended to inject the current as
far as possible from the analog input pins.
5. For ROM versions, it is forbidden to inject current on the NMI pin.
Symbol
Ratings
Maximum value
Unit
VDD - VSS
Supply voltage
7
V
VIN
Input voltage on any pin 1) & 2)
VSS-0.3 to VDD+0.3
VOUT
Output voltage on any pin 1) & 2)
VSS-0.3 to VDD+0.3
VESD(HBM)
Electro-static discharge voltage (Human Body Model)
3500
Symbol
Ratings
Maximum value
Unit
IVDD
Total current into VDD power lines (source)
3)
80
mA
IVSS
Total current out of VSS ground lines (sink)
3)
100
IIO
Output current sunk by any standard I/O and control pin
20
Output current sunk by any high sink I/O pin
40
Output current source by any I/Os and control pin
15
IINJ(PIN)
2) & 4)
Injected current on RESET pin
±5
Injected current on any other pin5)
±5
Symbol
Ratings
Value
Unit
TSTG
Storage temperature range
-60 to +150
°C
TJ
Maximum junction temperature
(see THERMAL CHARACTERISTICS section)
1
相关PDF资料
PDF描述
ST6203CN3/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO16
ST6209CB1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20
ST6220CB3/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20
ST6220CB6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20
ST6208CB1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20
相关代理商/技术参数
参数描述
ST6200CM-AUTO 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCUs WITH A/D CONVERTER, TWO TIMERS, OSCILLATOR SAFEGUARD & SAFE RESET
ST6200FNL 制造商:Pulse Electronics Corporation 功能描述:TRANSFORMER - Bulk 制造商:Pulse Electronics Corporation 功能描述:XFRMR 1:1 SONET/SDH E4/STM-1 SMD
ST6200FNLT 制造商:Pulse Electronics Corporation 功能描述:TRANSFORMER - Tape and Reel 制造商:Pulse Electronics Corporation 功能描述:XFRMR 1:1 SONET/SDH E4/STM-1 SMD
ST6200L 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:LOW VOLTAGE 8-BIT ROM MCUs WITH A/D CONVERTER,AND 16 PINS
ST6200LB1 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:LOW VOLTAGE 8-BIT ROM MCUs WITH A/D CONVERTER,AND 16 PINS