收藏本站
参数资料
型号： ST62T18CM3
厂商： STMICROELECTRONICS
元件分类： 微控制器/微处理器
英文描述： 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO20
封装： 0.300 INCH, PLASTIC, SOP-20
文件页数： 67/82页
文件大小： 937K
代理商： ST62T18CM3
Obsolete
Product(s)
- Obsolete
Product(s)
7/82
ST62T18C/E18C
1.2 PIN DESCRIPTIONS
VDD and VSS. Power is supplied to the MCU via
these two pins. VDD is the power connection and
VSS is the ground connection.
OSCin and OSCout. These pins are internally
connected to the on-chip oscillator circuit. A quartz
crystal, a ceramic resonator or an external clock
signal can be connected between these two pins.
The OSCin pin is the input pin, the OSCout pin is
the output pin.
RESET. The active-low RESET pin is used to re-
start the microcontroller.
TEST/V
PP. The TEST must be held at VSS for nor-
mal operation. If TEST pin is connected to a
+12.5V level during the reset phase, the EPROM/
OTP programming Mode is entered.
NMI. The NMI pin provides the capability for asyn-
chronous interruption, by applying an external non
maskable interrupt to the MCU. Schmitt trigger
characteristics. The user can select as option the
availability of an on-chip pull-up at this pin.
PA1-PA5. These 5 lines are organised as one I/O
port (A). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull outputs.
PA3/ARTIMout and PA4/ARTIMin can be used re-
spectively as output and input pins for the embed-
ded 8-bit Auto-Reload Timer.
In addition, PA1-PA5 can sink 20mA for direct LED
or TRIAC drive.
PB4...PB6. These 3 lines are organised as one I/O
port (B). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull outputs,
analog inputs for the A/D converter.
PD4...PD7. These 4 lines are organised as one I/O
port (portD). Each line may be configured under
software control as input with or without internal
pull-up resistor, input with interrupt generation and
pull-up resistor, analog input open-drain or push-
pull output. In addition, the pins PD5/TXD1 and
PD4/RXD1 can be used as UART output (PD5/
TXD1) or UART input (PD4/RXD1).
TIMER. This is the TIMER 1 I/O pin. In input mode,
it is connected to the prescaler and acts as ex-
ternal timer clock or as control gate for the internal
timer clock. In output mode, the TIMER pin outputs
the data bit when a time-out occurs.The user can
select as option the availability of an on-chip pull-
up at this pin.
7
相关PDF资料
PDF描述
ST62P28CB3/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP28
ST6218CB6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20
ST62P18CB1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20
ST6327B1 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
ST6375B1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
相关代理商/技术参数
参数描述
ST62T18CM6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI/UAR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST62T20CB3 功能描述:8位微控制器 -MCU ST6208C ST6209C ST6220C 8B MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST62T20CB6 功能描述:8位微控制器 -MCU OTP EPROM 4K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST62T20CB6 制造商:STMicroelectronics 功能描述:IC 8BIT MCU OTP 4K 62T20 DIP20
ST62T20CM6 功能描述:8位微控制器 -MCU OTP EPROM 4K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*