- 您现在的位置：买卖IC网 > PDF目录98146 > ST7260E2M1/XXX (STMICROELECTRONICS) 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24 PDF资料下载
参数资料
| 型号： | ST7260E2M1/XXX |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24 |
| 封装： | 0.300 INCH, LEAD FREE, PLASTIC, SOP-24 |
| 文件页数： | 3/118页 |
| 文件大小： | 2304K |
| 代理商： | ST7260E2M1/XXX |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页
ST7260
100/117
CONTROL PIN CHARACTERISTICS (Cont’d)
Figure 61. RESET pin protection when LVD is enabled.1)2)3)4)
Figure 62. RESET pin protection when LVD is disabled.1)
Note 1:
– The reset network protects the device against parasitic resets.
– The output of the external reset circuit must have an open-drain output to drive the ST7 reset pad. Otherwise the
device can be damaged when the ST7 generates an internal reset (LVD or watchdog).
– Whatever the reset source is (internal or external), the user must ensure that the level on the RESET pin can go
below the VIL max. level specified in section 13.9.1 on page 99. Otherwise the reset will not be taken into account
internally.
– Because the reset circuit is designed to allow the internal RESET to be output in the RESET pin, the user must en-
sure that the current sunk on the RESET pin is less than the absolute maximum value specified for IINJ(RESET) in
Note 2: When the LVD is enabled, it is recommended not to connect a pull-up resistor or capacitor. A 10nF pull-down
capacitor is required to filter noise on the reset line.
Note 3: In case a capacitive power supply is used, it is recommended to connect a 1 M
pull-down resistor to the RESET
pin to discharge any residual voltage induced by the capacitive effect of the power supply (this will add 5A to the power
consumption of the MCU).
Note 4: Tips when using the LVD:
– 1. Check that all recommendations related to ICCCLK and reset circuit have been applied (see notes above).
– 2. Check that the power supply is properly decoupled (100 nF + 10 F close to the MCU). Refer to AN1709 and
AN2017. If this cannot be done, it is recommended to put a 100 nF + 1M
pull-down on the RESET pin.
– 3. The capacitors connected on the RESET pin and also the power supply are key to avoid any start-up marginality.
In most cases, steps 1 and 2 above are sufficient for a robust solution. Otherwise: replace 10 nF pull-down on the
RESET pin with a 5 F to 20 F capacitor.”
0.01
F
ST72XXX
PULSE
GENERATOR
Filter
RON
VDD
WATCHDOG
LVD RESET
INTERNAL
RESET
EXTERNAL
Required
1 M
Optional
(note 6)
0.0 1
F
0.01
F
VDD
EXTERNAL
RESET
CIRCUIT
USER
VDD
4.7 k
Required
Recommended for EMC
ST72XXX
PULSE
GENERATOR
Filter
RON
VDD
WATCHDOG
INTERNAL
RESET
相关PDF资料 |
PDF描述 |
|---|---|
| ST72T141K2M6XXX | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34 |
| ST72T141K2M3XXX | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34 |
| ST72T141K2MARE | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34 |
| ST7FL09Y0MATRE | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDSO16 |
| ST7FL09Y0MBE | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST72611F1 | 制造商:STMicroelectronics 功能描述:LOW SPEED USB 8-BIT MCU WITH 3 ENDPOINTS,FLASH MEMORY, - Bulk |
| ST7263-EMU2 | 功能描述:仿真器/模拟器 ST7 Emulator Board RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2 |
| ST7265X-EVAL/MS | 制造商:STMicroelectronics 功能描述:ST6 EVAL BD - Bulk |
| ST7265X-EVAL/PFD | 制造商:STMicroelectronics 功能描述:USB FLASH EVAL - Bulk |
| ST7266 | 制造商:6940 功能描述:ST7266 |
发布紧急采购，3分钟左右您将得到回复。