参数资料
型号: ST7PLUSA2B6
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP8
封装: 0.300 INCH, ROHS COMPLIANT, PLASTIC, DIP-8
文件页数: 58/136页
文件大小: 1705K
代理商: ST7PLUSA2B6
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
Supply, reset and clock management
ST7LITEUS2, ST7LITEUS5
6
Supply, reset and clock management
The device includes a range of utility features for securing the application in critical
situations (for example in case of a power brown-out), and reducing the number of external
components.
6.1
Main features
Clock management
8 MHz internal RC oscillator (enabled by option byte)
External clock Input (enabled by option byte)
Reset sequence manager (RSM)
System integrity management (SI)
Main supply low voltage detection (LVD) with reset generation (enabled by option
byte)
Auxiliary voltage detector (AVD) with interrupt capability for monitoring the main
supply
6.2
Internal RC oscillator adjustment
The ST7 contains an internal RC oscillator with a specific accuracy for a given device,
temperature and voltage. It can be selected as the start up clock through the CKSEL[1:0]
option bits (see Section 14.1 on page 123). It must be calibrated to obtain the frequency
required in the application. This is done by software writing a 10-bit calibration value in the
RCCR (RC Control register) and in the bits [6:5] in the SICSR (SI Control Status register).
Whenever the microcontroller is reset, the RCCR returns to its default value (FFh), i.e. each
time the device is reset, the calibration value must be loaded in the RCCR. Predefined
calibration values are stored in Flash memory for 3.3 and 5 V VDD supply voltages at 25°C,
as shown in the following table.
Table 5.
Predefined RC oscillator calibration values
RCCR
Conditions
ST7LITEUS2/ST7LITEUS5 address
RCCRH0
VDD=5 V
TA=25 °C
fRC=8 MHz
DEE0h(1) (CR[9:2] bits)
1.
DEE0h, DEE1h, DEE2h and DEE3h are located in a reserved area butare special bytes containing also
the RC calibration values which are read-accessible only in user mode. If all the Flash space (including the
RC calibration value locations) has been erased (after the readout protection removal), then the RC
calibration values can still be obtained through these two addresses.
RCCRL0
DEE1h 1) (CR[1:0] bits)
RCCRH1
VDD=3.3 V
TA=25 °C
fRC=8 MHz
DEE2h 1) (CR[9:2] bits)
RCCRL1
DEE3h 1) (CR[1:0] bits)
相关PDF资料
PDF描述
ST7FLITEUSA5U6TR 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8
ST7PLUSA5U6TR 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
ST7PLUSA5B6 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP8
ST7PLUSA2M3 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8
ST7PMC1K2TC/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32
相关代理商/技术参数
参数描述
ST7PMC1K2B3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2B6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2T6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T6/ST7PMC1K2 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI