- 您现在的位置：买卖IC网 > PDF目录98147 > STK1743-D35I 0 TIMER(S), REAL TIME CLOCK, DIP28 PDF资料下载
参数资料
| 型号： | STK1743-D35I |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, DIP28 |
| 封装： | 0.600 INCH, MODULE, DIP-28 |
| 文件页数： | 11/12页 |
| 文件大小： | 314K |
| 代理商： | STK1743-D35I |
STK1743
January 2003
8
Document Control # ML0011 rev 0.0
STK1743 clock registers before reading clock data
to prevent reading of data in transition. Stopping the
internal register updates does not affect clock accu-
racy.
The updating process is stopped by writing a “1” to
the read bit (the second most significant bit in the
control register 1FF8), and will not restart until a “0”
is written to the read bit. The RTC registers can
then be read while the internal clock continues to
run.
Within one second after a “0” is written to the read
bit, all STK1743 registers are simultaneously
updated.
SRAM WRITE AND
SETTING THE CLOCK
A WRITE cycle is performed whenever E and W are
low. The address inputs must be stable prior to
entering the WRITE cycle and must remain stable
until either E or W goes high at the end of the cycle.
The data on the common I/O pins DQ
0-7 will be writ-
ten into the memory if it is valid t
DVWH before the end
of a W controlled WRITE or t
DVEH before the end of
an E controlled WRITE.
It is recommended that G be kept high during the
entire WRITE cycle to avoid data bus contention on
the common I/O lines. If G is left low, internal cir-
cuitry will turn off the output buffers t
WLQZ after W
goes low.
Setting the write bit (the MSB of the control register
1FF8) to a “1” halts updates to the STK1743 regis-
ters. The correct day, date and time can then be
written into the registers in 24-hour BCD format.
Resetting the write bit to “0” transfers those values
to the actual clock counters, after which the clock
resumes normal operation.
FREQUENCY TEST BIT
As shown in the RTC Register Map, bit 6 of the day
byte is the frequency test (FT) bit. When the FT bit
is set to logic “1”, the LSB of the seconds register
will toggle at 512Hz. When the seconds register is
being read, the DQ
0 line will toggle at 512Hz as
long as conditions for access remain valid (i.e., CE
low, OE low, WE high and the address for the sec-
onds register valid and stable). The FT bit must be
reset to “0” in order to resume reading the time
from the seconds register.
CLOCK ACCURACY
The STK1743 is guaranteed to be accurate to
within
± 1 minute per month at 25
°C. The part
requires no additional calibration, and temperature
variations will have a negligible effect in most appli-
cations.
DATA RETENTION MODE
During normal operation (V
CC ≥ 4.5V), the STK1743
can be accessed with standard SRAM READ and
WRITE
cycles. However, when V
CC falls below the
power-fail voltage, V
SWITCH (the voltage at which
write protection occurs), access to the internal clock
register and the SRAM is blocked. At this voltage,
SRAM
data is automatically stored to the integral
Nonvolatile Elements, and power for the clock oscil-
lator switches from the V
CC pin to the internal capac-
itor. The capacitor maintains clock activity and clock
data until V
CC returns to its nominal level.
SOFTWARE NONVOLATILE STORE
The STK1743 software STORE cycle is initiated by
executing sequential READ cycles from six specific
address locations. During the STORE cycle an erase
of the previous nonvolatile data is first performed,
followed by a program of the nonvolatile elements.
The program operation copies the SRAM data into
nonvolatile memory. Once a STORE cycle is initi-
ated, further input and output are disabled until the
cycle is completed.
Because a sequence of READs from specific
addresses is used for STORE initiation, it is impor-
tant that no other READ or WRITE accesses inter-
vene in the sequence or the sequence will be
aborted and no STORE or RECALL will take place.
To initiate the software STORE cycle, the following
READ
sequence must be performed:
1. Read address
0000 (hex)
Valid READ
2. Read address
1555 (hex)
Valid READ
3. Read address
0AAA (hex)
Valid READ
4. Read address
1FFF (hex)
Valid READ
5. Read address
10F0 (hex)
Valid READ
6. Read address
0F0F (hex)
Initiate STORE cycle
The software sequence must be clocked with E
controlled READs.
Once the sixth address in the sequence has been
entered, the STORE cycle will commence and the
SRAM
will be disabled. The clock addresses may be
相关PDF资料 |
PDF描述 |
|---|---|
| STK17CA8-W45I | REAL TIME CLOCK, PDIP40 |
| STK17T88-RF45TR | PROGRAMMABLE TIMER, PDSO48 |
| STK17T88-RF45 | PROGRAMMABLE TIMER, PDSO48 |
| STK17T88-RF25ITR | PROGRAMMABLE TIMER, PDSO48 |
| STK17TA8-R25I | REAL TIME CLOCK, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| STK17T88-RF25 | 功能描述:NVRAM 32Kbx8+RTC 2.7-3.6V RoHS:否 制造商:Maxim Integrated 数据总线宽度:8 bit 存储容量:1024 Kbit 组织:128 K x 8 接口类型:Parallel 访问时间:70 ns 电源电压-最大:5.5 V 电源电压-最小:4.5 V 工作电流:85 mA 最大工作温度:+ 70 C 最小工作温度:0 C 封装 / 箱体:EDIP 封装:Tube |
| STK17T88-RF25I | 功能描述:NVRAM 32Kbx8+RTC 2.7-3.6V RoHS:否 制造商:Maxim Integrated 数据总线宽度:8 bit 存储容量:1024 Kbit 组织:128 K x 8 接口类型:Parallel 访问时间:70 ns 电源电压-最大:5.5 V 电源电压-最小:4.5 V 工作电流:85 mA 最大工作温度:+ 70 C 最小工作温度:0 C 封装 / 箱体:EDIP 封装:Tube |
| STK17T88-RF25ITR | 功能描述:NVRAM 32Kbx8+RTC 2.7-3.6V RoHS:否 制造商:Maxim Integrated 数据总线宽度:8 bit 存储容量:1024 Kbit 组织:128 K x 8 接口类型:Parallel 访问时间:70 ns 电源电压-最大:5.5 V 电源电压-最小:4.5 V 工作电流:85 mA 最大工作温度:+ 70 C 最小工作温度:0 C 封装 / 箱体:EDIP 封装:Tube |
| STK17T88-RF25TR | 功能描述:NVRAM 32Kbx8+RTC 2.7-3.6V RoHS:否 制造商:Maxim Integrated 数据总线宽度:8 bit 存储容量:1024 Kbit 组织:128 K x 8 接口类型:Parallel 访问时间:70 ns 电源电压-最大:5.5 V 电源电压-最小:4.5 V 工作电流:85 mA 最大工作温度:+ 70 C 最小工作温度:0 C 封装 / 箱体:EDIP 封装:Tube |
| STK17T88-RF45 | 功能描述:NVRAM 32Kbx8+RTC 2.7-3.6V RoHS:否 制造商:Maxim Integrated 数据总线宽度:8 bit 存储容量:1024 Kbit 组织:128 K x 8 接口类型:Parallel 访问时间:70 ns 电源电压-最大:5.5 V 电源电压-最小:4.5 V 工作电流:85 mA 最大工作温度:+ 70 C 最小工作温度:0 C 封装 / 箱体:EDIP 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。