参数资料
型号: STM32F101VGT6
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP100
封装: 14 X 14 MM, 0.50 MM PTCH, ROHS COMPLIANT, LQFP-100
文件页数: 7/39页
文件大小: 752K
代理商: STM32F101VGT6
STM32F101xF, STM32F101xG
Description
Doc ID 17143 Rev 2
2.3.14
Voltage regulator
The regulator has three operation modes: main (MR), low power (LPR) and power down.
MR is used in the nominal regulation mode (Run)
LPR is used in the Stop modes.
Power down is used in Standby mode: the regulator output is in high impedance: the
kernel circuitry is powered down, inducing zero consumption (but the contents of the
registers and SRAM are lost)
This regulator is always enabled after reset. It is disabled in Standby mode.
2.3.15
Low-power modes
The STM32F101xF and STM32F101xG access line supports three low-power modes to
achieve the best compromise between low power consumption, short startup time and
available wakeup sources:
Sleep mode
In Sleep mode, only the CPU is stopped. All peripherals continue to operate and can
wake up the CPU when an interrupt/event occurs.
Stop mode
Stop mode achieves the lowest power consumption while retaining the content of
SRAM and registers. All clocks in the 1.8 V domain are stopped, the PLL, the HSI RC
and the HSE crystal oscillators are disabled. The voltage regulator can also be put
either in normal or in low power mode.
The device can be woken up from Stop mode by any of the EXTI line. The EXTI line
source can be one of the 16 external lines, the PVD output or the RTC alarm.
Standby mode
The Standby mode is used to achieve the lowest power consumption. The internal
voltage regulator is switched off so that the entire 1.8 V domain is powered off. The
PLL, the HSI RC and the HSE crystal oscillators are also switched off. After entering
Standby mode, SRAM and register contents are lost except for registers in the Backup
domain and Standby circuitry.
The device exits Standby mode when an external reset (NRST pin), a IWDG reset, a
rising edge on the WKUP pin, or an RTC alarm occurs.
Note:
The RTC, the IWDG, and the corresponding clock sources are not stopped by entering Stop
or Standby mode.
2.3.16
DMA
The flexible 12-channel general-purpose DMAs (7 channels for DMA1 and 5 channels for
DMA2) are able to manage memory-to-memory, peripheral-to-memory and memory-to-
peripheral transfers.
The two DMA controllers support circular buffer management, removing the need for user
code intervention when the controller reaches the end of the buffer.
Each channel is connected to dedicated hardware DMA requests, with support for software
trigger on each channel. Configuration is made by software and transfer sizes between
source and destination are independent.
DMA can be used with the main peripherals: SPI, I2C, USART, general-purpose and basic
timers TIMx, DAC and ADC.
相关PDF资料
PDF描述
STM32F101T4U6TR 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QCC36
STM32F101C6T6ATR 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QCC48
STM32F101R4T6XXX 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QFP64
STM32F101C4U6TR 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QCC48
STM32F101C6U6TR 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QCC48
相关代理商/技术参数
参数描述
STM32F101X4 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
STM32F101X4_10 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers
STM32F101X6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers, ADC and 4 communication interfaces
STM32F101X6_08 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Access line, advanced ARM-based 32-bit MCU with Flash memory, six 16-bit timers, ADC and seven communication interfaces
STM32F101X6_10 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Low-density access line, ARM-based 32-bit MCU with 16 or 32 KB Flash, 5 timers