参数资料
型号: STM8L162R8T3
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQFP64
封装: 10 X 10 MM, LQFP-64
文件页数: 22/116页
文件大小: 1229K
代理商: STM8L162R8T3
STM8L162R8, STM8L162M8
Functional overview
Doc ID 17959 Rev 1
IWDG: Independent watchdog
LCD: Liquid crystal display
POR/PDR: Power on reset / power-down reset
RTC: Real-time clock
SPI: Serial peripheral interface
SWIM: Single wire interface module
USART: Universal synchronous asynchronous receiver transmitter
WWDG: Window watchdog
3.1
Low power modes
The High density STM8L162xx devices support five low power modes to achieve the best
compromise between low power consumption, short startup time and available wakeup
sources:
Wait mode: CPU clock is stopped, but selected peripherals keep running. An internal
or external interrupt or a Reset can be used to exit the microcontroller from Wait mode
(WFE or WFI mode).
Low power run mode: The CPU and the selected peripherals are running. Execution
is done from RAM with a low speed oscillator (LSI or LSE). Flash memory and data
EEPROM are stopped and the voltage regulator is configured in Ultralow power mode.
The microcontroller enters Low power run mode by software and can exit from this
mode by software or by a reset.
All interrupts must be masked. They cannot be used to exit the microcontroller from this
mode.
Low power wait mode: This mode is entered when executing a Wait for event in Low
power run mode. It is similar to Low power run mode except that the CPU clock is
stopped. The wakeup from this mode is triggered by a Reset or by an internal or
external event (peripheral event generated by the timers, serial interfaces, DMA
controller (DMA1), comparators and I/O ports). When the wakeup is triggered by an
event, the system goes back to Low power run mode.
All interrupts must be masked. They cannot be used to exit the microcontroller from this
mode.
Active-halt mode: CPU and peripheral clocks are stopped, except RTC. The wakeup
can be triggered by RTC interrupts, external interrupts or reset.
Halt mode: CPU and peripheral clocks are stopped, the device remains powered on.
The wakeup is triggered by an external interrupt or reset. A few peripherals have also a
wakeup from Halt capability. Switching off the internal reference voltage reduces power
consumption. Through software configuration it is also possible to wake up the device
without waiting for the internal reference voltage wakeup time to have a fast wakeup
time of 5 s.
3.2
Central processing unit STM8
3.2.1
Advanced STM8 Core
The 8-bit STM8 core is designed for code efficiency and performance with an Harvard
architecture and a 3-stage pipeline.
It contains 6 internal registers which are directly addressable in each execution context, 20
addressing modes including indexed indirect and relative addressing, and 80 instructions.
相关PDF资料
PDF描述
STM8L162R8T6 8-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQFP64
STMPE2401TBR 24 I/O, PIA-GENERAL PURPOSE, PBGA36
STMPE801MTR 8 I/O, PIA-GENERAL PURPOSE, PDSO16
STMPS2262MTR 4 I/O, PIA-GENERAL PURPOSE, PDSO8
STN8810B2S12HPI 32-BIT, 264 MHz, RISC PROCESSOR, PBGA26
相关代理商/技术参数
参数描述
STM8L162R8T6 功能描述:8位微控制器 -MCU STM8L Ultra LP 8-Bit 64-Pin 64kB Flash RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
STM8L-DISCOVERY 功能描述:开发板和工具包 - 其他处理器 STM8L Ultra Low PWR ST-Link Included RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压:
STM8P151F36MCYTR 制造商:STMicroelectronics 功能描述:8 BITS MICROCONTR - Tape and Reel
STM8S/32-D/RAIS 功能描述:开发板和工具包 - 其他处理器 STM8S105C6 D-BRD ReVA Starter 128kB RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压:
STM8S/8-D/RAIS 功能描述:开发板和工具包 - 其他处理器 STMS903K3 D-BRD ReVA Starter 128kB RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: