- 您现在的位置：买卖IC网 > PDF目录98148 > STMPE801MTR (STMICROELECTRONICS) 8 I/O, PIA-GENERAL PURPOSE, PDSO16 PDF资料下载
参数资料
| 型号： | STMPE801MTR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8 I/O, PIA-GENERAL PURPOSE, PDSO16 |
| 封装： | SOP-16 |
| 文件页数： | 5/26页 |
| 文件大小： | 399K |
| 代理商： | STMPE801MTR |
STMPE801
I2C module
13/26
5.8
Read operation
A write is first performed to load the register address into the Address Counter but without
sending a Stop condition. Then, the bus master sends a reStart condition and repeats the
Device Address with the R/W bit set to 1. The slave device acknowledges and outputs the
content of the addressed byte. If no more data is to be read, the bus master must not
acknowledge the byte and terminates the transfer with a Stop condition.
If the bus master acknowledges the data byte, then it can continue to perform the data
reading. To terminate the stream of data byte, the bus master must not acknowledge the
last output byte and follow by a Stop condition. If the address of the register written into the
Address Counter falls within the range of addresses that has the auto-increment function,
the data being read will be coming from consecutive addresses, with the internal Address
Counter automatically increments after each byte output. After the last memory address,
the Address Counter 'rolls-over' and the device continue to output data from the memory
address of 0x00. Similarly, for the address of register that falls within non-increment range
of addresses, the output data byte comes from the same address (which is the address
pointed by the Address Counter).
5.9
Acknowledgement in read operation
For the above read command, the slave device waits, after each byte read, for an
acknowledgement during the ninth bit time. If the bus master does not drive the SDA to low
state, then the slave device terminates and switches back to its idle mode, waiting for the
next command.
5.10
Write operations
A write is first performed to load the register address into the Address Counter without
sending a Stop condition. After the bus master receives an acknowledgement from the
slave device, it may start to send a data byte to the register (pointed by the Address
Counter). The slave device again acknowledges and the bus master terminates the transfer
with a Stop condition.
If the bus master would like to continue to write more data, it can just continue write
operation without issuing the Stop condition. Whether the Address Counter auto-
increments or not after each data byte write, depends on the address of the register written
into the Address Counter. After the bus master writes the last data byte and the slave
device acknowledges the receipt of the last data, the bus master may terminates the write
operation by sending a Stop condition. When the Address Counter reaches the last
memory address, it 'rolls-over' on the next data byte write.
相关PDF资料 |
PDF描述 |
|---|---|
| STMPS2262MTR | 4 I/O, PIA-GENERAL PURPOSE, PDSO8 |
| STN8810B2S12HPI | 32-BIT, 264 MHz, RISC PROCESSOR, PBGA26 |
| STN8810BES12HPBE | 32-BIT, 264 MHz, RISC PROCESSOR, PBGA26 |
| STP1012PGA-110 | 32-BIT, 110 MHz, RISC PROCESSOR, CPGA321 |
| STP1012PGA-70A | 32-BIT, 70 MHz, RISC PROCESSOR, CPGA321 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| STMPE801QTR | 功能描述:接口-I/O扩展器 8B port expander Xpander logic RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| STMPE811 | 制造商:STMicroelectronics 功能描述:Controller with 8-bit GPIO expander |
| STMPE811_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit port expander with advanced touchscreen controller |
| STMPE811_09 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Advanced resistive touch screen controller with 8-bit GPIO expander |
| STMPE811QTR | 功能描述:接口-I/O扩展器 8-BIT PORT EXPANDER W/ADV TOUCHSCREEN RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。