参数资料
型号: STR752FR2T7
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 32-BIT, FLASH, 48 MHz, RISC MICROCONTROLLER, PQFP64
封装: 10 X 10 MM, ROHS COMPLIANT, LQFP-64
文件页数: 8/84页
文件大小: 1656K
代理商: STR752FR2T7
Pin description
STR750Fxx STR751Fxx STR752Fxx STR755Fxx
Port reset state
The reset state of the I/O ports is GPIO input floating. Exceptions are P1[19:16] and P0.13
which are configured as JTAG alternate functions:
The JTAG inputs (JTDI, JTMS and JTDI) are configured as input floating and are ready
to accept JTAG sequences.
The JTAG output JTDO is configured as floating when idle (no JTAG operation) and is
configured in output push-pull only when serial JTAG data must be output.
The JTAG output RTCK is always configured as output push-pull. It outputs '0' level
during the reset phase and then outputs the JTCK input signal resynchronized 3 times
by the internal AHB clock.
The GPIO_PCx registers do not control JTAG AF selection, so the reset values of
GPIO_PCx for P1[19:16] and P0. 13 are the same as other ports. Refer to the GPIO
section of the STR750 Reference Manual for the register description and reset values.
P0.11 and P0.00 are sampled by the boot logic after reset, prior to fetching the first
word of user code at address 0000 0000h.
When booting from SMI (and only in this case), the reset state of the following GPIOs is
"SMI alternate function output enabled":
P0.07 (SMI_DOUT)
P0.05 (SMI_CLK)
P0.04 (SMI_CS0)
P0.06 (SMI_DIN)
Note that the other SMI pins: SMI_CS1,2,3 (P0.12, P0.11, P0.10) are not affected.
To avoid excess power consumption, unused I/O ports must be tied to ground.
Table 6.
STR750F pin description
Pin n°
Pin name
Ty
p
e
Input
Output
Usab
le
i
n
Stan
db
y
Main
function
(after
reset)
Alternate function
LQ
FP10
0
(1
)
LF
BG
A100
LQ
FP64
(2)
LFBGA64
In
pu
tL
e
vel
floating
pu
/p
d
Ext.
int
/W
ake-
u
p
C
a
pa
bi
li
ty
OD
(3)
PP
1B1
1
B1
P1.12 /
ADC_IN13
I/O
TT
X
XEIT12
O8
X
Port 1.12
ADC: Analog
input 13
2B2
2
C2
P0.02 /
TIM2_OC1 /
ADC_IN0
I/O
TT
X
XEIT0
O8
X
Port 0.02
TIM2: Output
Compare 1(4)
ADC: Analog
input 0
3B3
3
C1
P0.01 / TIM0_TI1
/ MCO
I/O
TT
X
XO8
X
Port 0.01
TIM0: Input
Capture / trigger
/ external clock 1
Main Clock
Output
4C2
4
C3
P0.00 /
TIM0_OC1 /
BOOT0
I/O
TT
X
XO8
X
Port 0.00 /
Boot mode
selection
input 0
TIM0: Output Compare 1
5
C1
P0.31 / TIM1_TI2
I/O
TT
X
XO2
X
Port 0.31
TIM1: Input Capture / trigger /
external clock 2
6D2
P0.30 /
TIM1_OC2
I/O
TT
X
XO2
X
Port 0.30
TIM1: Output Compare 2
相关PDF资料
PDF描述
STR751FR1T6 32-BIT, FLASH, 48 MHz, RISC MICROCONTROLLER, PQFP64
STR751FR0H6 32-BIT, FLASH, 48 MHz, RISC MICROCONTROLLER, PBGA64
STR750FV2H6 32-BIT, FLASH, 48 MHz, RISC MICROCONTROLLER, PBGA100
STR750FV1H6 32-BIT, FLASH, 48 MHz, RISC MICROCONTROLLER, PBGA100
STR752FR0H7 32-BIT, FLASH, 48 MHz, RISC MICROCONTROLLER, PBGA64
相关代理商/技术参数
参数描述
STR752FXX 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:ARM7TDMI-S⑩ 32-bit MCU with Flash, SMI, 3 std 16-bit timers, PWM timer, fast 10-bit ADC, I2C, UART, SSP, USB and CAN
STR755FR0 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:ARM7TDMI-S? 32-bit MCU with Flash, SMI, 3 std 16-bit timers, PWM timer, fast 10-bit ADC, I2C, UART, SSP, USB and CAN
STR755FR0H6 功能描述:ARM微控制器 - MCU 16/32-BITS MICROS RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
STR755FR0T6 功能描述:ARM微控制器 - MCU 32Bit MCU with Flash STR73xF ARM7TDMI RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
STR755FR1 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:ARM7TDMI-S⑩ 32-bit MCU with Flash, SMI, 3 std 16-bit timers, PWM timer, fast 10-bit ADC, I2C, UART, SSP, USB and CAN