- 您现在的位置：买卖IC网 > PDF目录19388 > SWS600L-3 (TDK-Lambda Americas Inc)POWER SUPPLY 3.3V 120A SGL OTPT PDF资料下载
参数资料
| 型号： | SWS600L-3 |
| 厂商： | TDK-Lambda Americas Inc |
| 文件页数： | 12/19页 |
| 文件大小： | 0K |
| 描述： | POWER SUPPLY 3.3V 120A SGL OTPT |
| 产品目录绘图： | Enclosed Case |
| 标准包装： | 1 |
| 系列： | SWS |
| 类型： | 标准产品 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 85 ~ 265VAC |
| 输出 - 1 @ 电流（最大）： | 3.3 VDC @ 120A |
| 功率（瓦特）： | 600W |
| 电源类型： | 开关（封闭框架） |
| 应用： | 商用 |
| 安装类型： | 底座安装 |
| 尺寸/尺寸： | 7.48" L x 4.72" W x 2.40" H（190.0mm x 120.0mm x 61.0mm） |
| 工作温度： | -20°C ~ 74°C |
| 效率： | 72% |
| 电源（瓦特）- 最大： | 396W |
| 批准： | CSA，DENAN，EN，IEC，UL |
| 其它名称： | 285-1789 SWS600L3 |
SWS 600L, 1000L
4. Functions and Precautions
Input Voltage Range
Input voltage range is single phase 85 - 265VAC (47 - 63Hz) or
120 - 350VDC. Input voltage, which is out of speci?cation, may
ALM
Vmax=50V
Imax=10mA
cause unit damage. Rated input voltage for safety standard
application is 100AC-240VAC (50/60Hz).
Ｇ 1
Output Voltage Range
Output voltage is set to the rated value at shipment. V.ADJ trim-
mer on the front panel side can be used to adjust the output
voltage within the range speci?ed (refer to speci?cations for
adjustable range).
To turn the trimmer clockwise, the output voltage will be in-
creased. Take note when the output voltage is increased ex-
cessively, over voltage protection (OVP) function may trigger
and output voltage will be shut down.
Over Voltage Protection (OVP)
The OVP function (inverter shutdown method, manual re-
set type) is provided. OVP function operates within speci? ed
range (refer to speci? cation) of the rated output voltage value
and the output will be shut down when OVP function triggers
Remote Sensing (+S, -S terminal)
This function compensates voltage drop of wiring from output
terminals to load terminals. Connect “+S” terminal to “+” termi-
nal of load and “-S” terminal to “-” terminal of load with sensing
wires. The total line voltage drop (+ side line and - side line) shall
be less than 0.3V. In case that sensing lines are too long, it is
necessary to put an electrolytic capacitor in following places.
(1) across the load terminal,
(2) between “+S” terminal and “+V ” terminal,
(3) between “-S” terminal and “-V ” terminal.
(refer to speci?cations for OVP range of each models). To reset
OVP, remove the input of power supply for a few minutes, and
then re-input. Or, use CNT to reset (remote ON/OFF : OFF to
ON). OVP value is ?xed and not to be adjusted externally. Never
CN1
+Vm
+S
-S
-Vm
apply more than rated output voltage to output terminal, which
may lead to damage. In the case of inductive load, use decou-
pling diode at output line.
+V
-V
+
+
+
-
Load
Over Current Protection (OCP)
The OCP function is provided. OCP characteristic is constant
current limiting, automatic recovery. OCP function operates
when the output current exceeds 105% (24V output model:
101% of peak current) of maximum DC output current speci-
?cation. The output will be automatically recovered when the
overload condition is cancelled. Never operate the unit under
over current or shorted conditions for more than 30 seconds,
which may lead to damage. OCP setting is ?xed and not to be
adjusted externally.
Over Temperature Protection (OTP)
The OTP function (manual reset type) is provided. When ambi-
ent or internal temperature rises abnormally, OTP function op-
erates and output will be shut down. After shut down, remove
the input and cool it down to reset OTP. Then re-input.
Power Failure Detection Circuit (ALM)
Power failure detection circuit is provided. ALM (Alarm) signal
will turn“High”level to indicate the abnormal status when con-
verter stops. Please take note in parallel or N+1 operation at light
load condition, maybe only one of the power supply operates
When the function of remote sensing is not used, connect +S
terminal to +Vm terminal, and -S terminal to -Vm terminal by the
attachment connector.
If remote sensing terminals are opened, the stability and the
accuracy of the output deteriorated. Therefore, terminal +S, -S
must be connected.
Remote ON/OFF Control
Remote ON/OFF control is provided.
Using this function, output on/off is allowed to control without
input voltage on/off.
(1) The maximum input voltage to CNT2 terminal is 12V, and the
maximum allowable reverse voltage is -1V; Current ?ow into
CNT2 is 5mA typical and 12mA maximum.
(2) A switch and relay or a transistor can be used as ON/OFF switch.
(3) Remote ON/OFF control circuit is isolated from the input
and output by a photo-coupler and can be controlled re-
gardless of the output potential (+ or -). Connect TOG termi-
nal to ground of control signal.
Specifications of remote ON/OFF
CNT2-TOG current or voltage condition:
and other power supply stops. When the built-in FAN motor of
this power supply unit stops, ALM signal will turn to “High” too.
If the output voltage is decreased to less than 20% of rated
voltage, or decreased rapidly through an external adjustment
mechanism when load is light, the ALM signal may turn “High”.
The ALM signal is isolated from input and output by a photo-
mosfet. It uses the open collector method shown as below.
Connection method
Output on
SW Logic
Output off
Pin
(a)
SW open
(0.1mA max)
SW close
(3mA min)
CNT2, TOG
(b) (c)
SW open SW close
(0.1mA max) (0.5V max)
SW close SW open
(3mA min) (0.1mA max)
CNT1, CNT2, TOG, G2 CNT1, CNT2, TOG, G2
12
?All specifications are subject to change without notice.
相关PDF资料 |
PDF描述 |
|---|---|
| MC7808BT | IC REG LDO 8V 1A TO220AB |
| TLJA476M010R0600 | CAP TANT 47UF 10V 20% 1206 |
| MC7808ACT | IC REG LDO 8V 1A TO220AB |
| ADSP-BF523KBCZ-6C2 | IC DSP CTRLR 24B W/CODEC 289BGA |
| MC7806CT | IC REG LDO 6V 1A TO220AB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SWS600L36 | 制造商:TDK-Lambda Corporation 功能描述:AC/DC Power Supply Single-OUT 36V 18A 648W 制造商:TDK-Lambda Corporation 功能描述:AC-DC,115-230VAC,OUTPUT 36V 18A,648W - Bulk |
| SWS600L-36 | 功能描述:线性和开关式电源 648W 36V 18A AC-DC, 115-230VAC RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
| SWS600L48 | 制造商:TDK-Lambda Corporation 功能描述:AC/DC Power Supply Single-OUT 48V 15A 624W 制造商:TDK-Lambda Corporation 功能描述:AC-DC,115-230VAC,OUTPUT 48V 13A,624W - Bulk |
| SWS600L-48 | 功能描述:线性和开关式电源 624W 48V 13A AC-DC, 115-230VAC RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
| SWS600L5 | 制造商:TDK-Lambda Corporation 功能描述:AC/DC Power Supply Single-OUT 5V 120A 600W 制造商:TDK-Lambda Corporation 功能描述:AC/DC PS SGL-OUT 5V 120A 600W - Bulk |
发布紧急采购，3分钟左右您将得到回复。