参数资料
| 型号： | SY88149NDLMG TR |
| 厂商： | Micrel Inc |
| 文件页数： | 2/13页 |
| 文件大小： | 0K |
| 描述： | IC LIMITING AMP 1.25GBPS 16QFN |
| 特色产品： | SY88149NDL Limiting Post Amplifier |
| 标准包装： | 1 |
| 类型： | 限幅后置放大器 |
| 应用： | 光纤学网络 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VFQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN（3x3） |
| 包装： | 标准包装 |
| 其它名称： | 576-4003-6 |
Micrel, Inc.
SY89838U
May 2008
M9999-051308-D
hbwhelp@micrel.com or (408) 955-1690
10
Case #4 Input Clock Failure: Switching from the
selected clock input stuck in an undetermined state to
a valid clock input (RPE enabled)
If CLK1 fails to an undetermined state (e.g., amplitude
falls below the 100mV (VIN) minimum single-ended
input limit, or 200mV differentially) before the RPE
MUX selects CLK2 (using the SEL pin), the switchover
to the valid clock CLK2 will occur either following Case
#2 or Case #3, depending on the last valid state at the
CLK1.
If the selected input clock fails to a floating, static, or
extremely low signal swing, including 0mV, the FSI
function will eliminate any metastable condition and
guarantee a stable output signal. No ringing and no
undetermined state will occur at the output under
these conditions.
Please note that the FSI function will not prevent duty
cycle distortions or runt pulses in case of a slowly
deteriorating (but still toggling) input signal. Due to the
FSI function, the propagation delay will depend on rise
and fall time of the input signal and on its amplitude.
Refer to “Typical Operating Characteristics” for more
detailed information.
Power-On Reset (POR) Description
The SY89838U includes an internal power-on reset
(POR) function to ensure the RPE logic starts-up in a
known logic state once the power-supply voltage is
stable. An external capacitor connected between VCC
and the CAP pin (pin 10) controls the delay for the
power-on reset function.
Calculation of the required capacitor value is based on
the time the system power supply needs to power up
to a minimum of 2.3V. The time constant for the
internal power-on-reset must be greater than the time
required for the power supply to ramp up to a minimum
of 2.3V.
The following formula describes this relationship:
C(F) ≥
)
/
(
12
)
(
F
ms
t
dPS
As an example, if the time required for the system
power supply to power up past 2.3V is 12ms, the
required capacitor value on pin 10 would be:
C(F) ≥
)
/
(
12
F
ms
C(F) ≥
F
1
CLK1
CLK2
SEL
Select CLK 1
Select CLK 2
OUTPUT
as in case #2
as in case #3
相关PDF资料 |
PDF描述 |
|---|---|
| AD5629RBCPZ-1-RL7 | IC DAC 12BIT I2C/SRL 16LFCSP-WQ |
| AD5326ARU | IC DAC 12BIT QUAD W/BUFF 16TSSOP |
| LTC1654IGN#TRPBF | IC D/A CONV 14BIT R-R DUAL16SSOP |
| VE-2WD-IV-F4 | CONVERTER MOD DC/DC 85V 150W |
| SY88913VKG | IC AMP LIMITING POST HS 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SY88212L | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3.3V, 2.5Gbps Laser Diode Driver |
| SY88212L_10 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3.3V, 2.5Gbps Laser Diode Driver |
| SY88212LMG | 功能描述:激光驱动器 3.3V, 2.5 Gbps LDD with APC and monitor function - 24 pin MLF Green RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| SY88212LMG TR | 功能描述:激光驱动器 3.3V, 2.5 Gbps LDD with APC and monitor function - 24 pin MLF Green RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| SY88212MGTR | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3.3V, 2.5Gbps Laser Diode Driver |
发布紧急采购，3分钟左右您将得到回复。