- 您现在的位置：买卖IC网 > PDF目录5475 > T11-2-10.0A-01-11AL-V (Sensata Technologies/Airpax)CIRCUIT BREAKER TOGGLE SP 10A PDF资料下载
参数资料
| 型号： | T11-2-10.0A-01-11AL-V |
| 厂商： | Sensata Technologies/Airpax |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | CIRCUIT BREAKER TOGGLE SP 10A |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 723-1272 |
HOW TO ORDER
The ordering code for the SNAPAK ? circuit protectors may be determined by following the steps in the decision tables shown here.
Push-To-Reset 2
Two Pole ?
Shunt Circuit Protector
Single pole (-1) and series only
Series w/ Silver Aux. Switch ???
when 1st decision "S" is
Thecodinggivenpermits
a self-assigning part
number, with certain
limitations (due to the
adaptability of magnetic
protectors to complex
circuits), requires a
factory-assigned part
number.
The example shown is the
code for a paddle handle,
single pole (UL
construction), series
circuit protector designed
for operation of a 50/60Hz/
DC circuit. A slow time
delay and rating of 5
amperes has been
indicated. Handle color is
black, and a bright nickel
knurled nut, vertical mount
(ON-OFF) indicator plate
and locking ring are to be
supplied.
1 First Decision
Handle Poles Con gurations* Terminals
T Paddle Handle 1 Single Pole ? 0 Switch Only (Note E) Quick Connects (leave blank)
PP Push-Pull 4 Single Pole ?? 1 Series Circuit Protector S Screw Terminals,
PR 3
R Rocker 5 Two Pole ?? 4 Relay Circuit Protector ???? (5th decision, group V - screw
terminal option is required
CR Rocker ** 5
CPP Push-Pull ** 6 Series w/ Gold Aux. Switch ??? speci ed)
CPR Push to Reset ** 9 Mixed Construction (2 Pole Only)
? UL & CSA Construction
?? Non UL & CSA Construction
??? Auxilary Switch is located in the left hand pole (viewed from terminal end)
???? Does not meet spacings for many IEC / VDE equipment specs.
Consult factory for additional information.
* Multi-pole units with mixed construction, poles numbered left to right when viewed
from terminal end. Shunt or relay construction available in pole 2 only, other pole must be a series
or switch only construction.
**UL 489A listed, available in 1 pole series or series w/silver aux. switch. DC delay only
T11 - 2- 5.00A - 01-11AL- V
CR, CPP, CPR only available in these delays
Todeterminetheordering
code for your particular
SNAPAK ? unit, simply
follow the steps shown,
then fill in the letters and/
or numbers in the boxes.
Space is available on the
circuit breaker label for
your part number (up to 12
digits). You may then use
your own part number to
place an order or as a
reference for further
questions you may have.
This option does require a
factory assigned part
number for traceability to
your drawing or internal
part number.
Notes:
1
2 Second Decision
Frequency & Delay
-0 Instant DC-50/60 Hz
-1 Fast DC-50/60 Hz
-2 Slow DC-50/60 Hz
-3 Fast w/ Inertia Wheel
DC-50/60 Hz
-4 Slow w/ Inertia Wheel
DC-50/60 Hz
-41* Fast 400 Hz***
-42* Slow 400 Hz*
-49* Instant 400 Hz
-51 Fast DC +
-52 Slow DC +
-59 Instant DC +
-61 Fast 50/60 Hz*
-62 Slow 50/60 Hz*
-69 Instant 50/60 Hz
- S Switch Pole or Special Delay
* 20 amps max for 400Hz
**For addition of Inertia Delay an "F" may
be added to delay 41, 42, 51, 52, 61, 62 only
+
3 Third Decision
Rated Current
Circuit Breaker Construction
Use three numbers to print required
current value between .100 amps
minimum and 30.0 amps maximum.
For example, use:
.100 or 2.00 or 10.0
Switch Only Construction
-SW Maintained SPST & DPST
Note: 20.0 amps max for 400 Hz units.
A A neon bulb is provided when specified for 120Vac and 250Vac operation. For operation
at 120Vac a 33,000 ohm, 1/2 watt external resistor is required. At 250Vac a 100,000
ohm, 1 watt external resistor is required.
B An LED with 750 ft. L @ 20mA is provided in the center of the handle. Maximum power
dissipation @ 25°C is 135mW. Continuous forward current is 20mA. Forward voltage,
typical, is 1.6v at 20mA. Reverse current, typical, is 100mA @ 3.0 volts. An external
resistor may be required to limit current to these values.
C When ordering Paddle Handles, you may choose one item from each hardware group to add to 5th
decision if such items are desired. For example, “-11ALCA” would indicate a bright nickel knurled nut,
plus a vertical mount indicator, plus a locking ring, plus #8-32 screw terminal, straight with tabs.
D All units except Rocker units will have (1) hex nut installed as standard hardware for the back of a
panel. The choices in the fifth decision table are intended for the front or visible side of the panel and
are offered for Paddle Handle configuration only. Push-Pull and Push-to-Reset configurations include
one (1) panel nut and one (1) hex nut as standard hardware.
E Switch only — no current overload protection provided.
67
SNAPAK ? Series - Decision Tables
F. CCC Approval - If CCC is required on this product, please inform Sensata to have this product
manufacturered in our China facility
相关PDF资料 |
PDF描述 |
|---|---|
| SMBJ20CA-13 | TVS BI-DIR 20V 600W SMB |
| MP2-SS030-51S1-TR30 | CONN SOCKET 2-FB 30POS 5ROW |
| 51726-10201600A0LF | R/A HEADER POWERBLADE |
| R11-62-10.0A-B01CH-S-V | CIRCUIT BREAKER MAGNETTIC 10A |
| 72377-1221LF | 2 X 5 CONNECTOR SUB-ASSY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| T11-2-11.0A-01-31A-V | 制造商:Sensata Technologies 功能描述:1 Pole |
| T11-211-0.2 | 功能描述:CIRCUIT BRKR SP RESET 0.2A SCREW RoHS:是 类别:过电压，电流，温度装置 >> 断路器 系列:T11 标准包装:20 系列:T12 断路器类型:热敏式 电压:240VAC，28VDC 电流 - 跳闸(It):300mA 极数:1 触动器类型:推推型 安装类型:面板安装 其它名称:4410.07944410.0794-ND |
| T11-211-0.3 | 功能描述:CIRCUIT BRKR SP RESET 0.3A SCREW RoHS:是 类别:过电压，电流，温度装置 >> 断路器 系列:T11 标准包装:20 系列:T12 断路器类型:热敏式 电压:240VAC，28VDC 电流 - 跳闸(It):300mA 极数:1 触动器类型:推推型 安装类型:面板安装 其它名称:4410.07944410.0794-ND |
| T11-211-0.4 | 功能描述:CIRCUIT BRKR THERMAL 400MA 1POLE RoHS:是 类别:过电压，电流，温度装置 >> 断路器 系列:T11 标准包装:20 系列:T12 断路器类型:热敏式 电压:240VAC，28VDC 电流 - 跳闸(It):300mA 极数:1 触动器类型:推推型 安装类型:面板安装 其它名称:4410.07944410.0794-ND |
| T11-211-0.5 | 功能描述:CIRCUIT BRKR SP RESET 0.5A SCREW RoHS:是 类别:过电压，电流，温度装置 >> 断路器 系列:T11 标准包装:20 系列:T12 断路器类型:热敏式 电压:240VAC，28VDC 电流 - 跳闸(It):300mA 极数:1 触动器类型:推推型 安装类型:面板安装 其它名称:4410.07944410.0794-ND |
发布紧急采购，3分钟左右您将得到回复。