- 您现在的位置：买卖IC网 > PDF目录272818 > TA7259P BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDIP16 PDF资料下载
参数资料
| 型号： | TA7259P |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDIP16 |
| 封装： | 0.500 INCH, 2.54 MM PITCH, PLASTIC, HDIP-14/16 |
| 文件页数： | 18/18页 |
| 文件大小： | 423K |
| 代理商： | TA7259P |
TA7259P/F/FG
2006-4-14
9
Notes on handling the IC
Motor drive ICs are easily affected by parasitic vibration and unnecessary feedback. This is because the
number of high impedance pins, such as position sensing inputs and control signal inputs, is large, and the
output current value is high and switched.
Moreover, because it is coil loading, care must be taken not to allow the impulse to destroy the IC during
ON/OFF switching. Especially when using a high voltage supply (Vcc is 18V or more), care must be taken not to
apply voltage and current to the output transistor which exceed the specification. Use of a supply voltageof 18V
or less is recommended. Pay particular attention to the notes above when using a supply voltage over 18V.
(1) Notes in designing reliability
) Do not expose the output transistor of the internal IC to high voltage and current,
especially, in motor lock status, ON/OFF switching of Vcc, output short-circuiting, etc.)
) The output condenser for ringing absorption should be as small as possible because the output
transistor can be destroyed by the charge-discharge current of this condenser. When there is a
problem, adjusting the capacity of the condenser, the connecting position and the connecting method
(delta or star), and inserting a series resistor (of a few to dozens of ) to the condenser and series
should provide the oscillating protection explained later.
) In mounting to the print-board, do not stress the FIN, and solder for only a few seconds at 260 .
) Using the large earth area of the print-board to release heat from the FIN is effective in ensuring
reliability.
(2) Notes in wiring
To protect from parasitic vibration, design the print-pattern following the method below.
)
The output coil current path must be separated from other GND lines because a switched high
current flows in this path. It is very important that the line (RF pin RF resister GND) should not
be of a common impedance with other circuits.
If the above is impossible or the oscillation cannot be removed completely, connect the condenser
(0.01 0.1F) and RF in parallel.
2.
TA7259P/F/FG
Avoid common impedance with other circuits
Fig. 2
相关PDF资料 |
PDF描述 |
|---|---|
| TRU050-TFLCA | PHASE LOCKED LOOP, CDIP16 |
| TRU050-THLGA | PHASE LOCKED LOOP, CDIP16 |
| TCM852EOA | SWITCHED CAPACITOR CONVERTER, 100 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC170CPE | SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDIP16 |
| TB6537PG | BRUSHLESS DC MOTOR CONTROLLER, PDIP18 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TA7259P(5) | 制造商:Toshiba America Electronic Components 功能描述: |
| TA7259P(LB) | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:DC MOTOR DRIVER IC |
| TA7259P_06 | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:3-PHASE BRUSHLESS DC MOTOR DRIVER IC |
| TA7262 | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:DC MOTOR DRIVER (3 PHASE Bi-DIRECTIONAL) |
| TA7262F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:DC MOTOR DRIVER (3 PHASE Bi-DIRECTIONAL) |
发布紧急采购，3分钟左右您将得到回复。