- 您现在的位置：买卖IC网 > PDF目录98158 > TAS3103DBTG4 (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PDSO38 PDF资料下载
参数资料
| 型号： | TAS3103DBTG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO38 |
| 封装： | GREEN, PLASTIC, TSSOP-38 |
| 文件页数： | 96/148页 |
| 文件大小： | 1247K |
| 代理商： | TAS3103DBTG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页当前第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页
220
2.3.2.2 I2C Slave Mode Operation
The I2C slave mode is the mode that must be used if it is required to change configuration parameters (other than
volume via the GPIO pins for the I2C master mode) during operation. The I2C slave mode is also the only I2C mode
that provides access to the spectrum analyzer and VU meter outputs. Configuration downloads from a master device
can be used to replace the I2C master mode EEPROM download.
For I2C read commands, the TAS3103 responds with data, a byte at a time, starting at the subaddress assigned, as
long as the master device continues to respond with acknowledges. If a given subaddress does not use all 32 bits,
the unused bits are read as logic 0. I2C write commands, however, are treated in accordance with the data assignment
for that address space. If a write command is received for a biquad subaddress, the TAS3103 expects to see five
32-bit words. If fewer than five data words have been received when a stop command (or another start command)
is received, the data received is discarded. If a write command is received for a mixer coefficient, the TAS3103
expects to see only one 32-bit word.
Supplying a subaddress for each subaddress transaction is referred to as random I2C addressing. The TAS3103 also
supports sequential I2C addressing. For write transactions, if a subaddress is issued followed by data for that
subaddress and the fifteen subaddresses that follow, a sequential I2C write transaction has taken place, and the data
for all 16 subaddresses is successfully received by the TAS3103. For I2C sequential write transactions, the
subaddress then serves as the start address and the amount of data subsequently transmitted, before a stop or start
is transmitted, determines how many subaddresses are written to. As was true for random addressing, sequential
addressing requires that a complete set of data be transmitted. If only a partial set of data is written to the last
subaddress, the data for the last subaddress is discarded. However, all other data written is accepted; just the
incomplete data is discarded.
The GPIO subaddresses and most reserved read-only and factory test subaddresses require the downloading of four
bytes of zero-valued spacer data in order to proceed to the next subaddress. However, there are five exceptions to
this rule and Table 24 lists the subaddresses of these fexceptions and the number of zero-valued bytes that must
be written.
Table 24. Four Byte Write Exceptions—Reserved and Factory-Test I2C Subaddresses
SUB-ADDRESS
NUMBER OF ZERO-VALUED BYTES
THAT MUST BE WRITTEN
0xC9
8
0xED
8
0xFD
10 (0xA)
0xFE
2
0xFF
1
The TAS3103 can always receive sequential I2C addressing write data without issuing wait states. If it is desired to
download data to all subaddresses using one sequential write transaction, spacer data for the reserved, GPIO,
read-only, and factory-test subaddresses must be supplied as per Table 23 and Table 24.
The TAS3103 also supports sequential read transactions. When an I2C subaddress assignment write transaction is
followed by a read transaction, the TAS3103 outputs the data for that subaddress, and then continue to output data
for the subaddresses that follow as long as the master continues to issue data received acknowledges. Except for
two exceptions, the TAS3103 outputs four bytes of zero-valued data for reserved and factory-test subaddresses. The
subaddresses of the exceptions and the number of bytes supplied by the TAS3103 for each exception are given in
Table 25. If a GPIO port is assigned as an output port, a logic 0 bit value is supplied by the TAS3103 for this GPIO
port in response to a read transaction at subaddress 0xEE.
CAUTION: Sequential write transactions must be in ascending subaddress order. The
TAS3103 does not wrap around from subaddress 0xFF to 0x00.
Sequential read transactions wrap around from subaddress 0xFF to 0x00.
相关PDF资料 |
PDF描述 |
|---|---|
| TAS3202PAGR | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS3202PAG | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS3204PAGR | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS3204PAG | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS3218IPZPR | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS3103DBTR | 功能描述:音频 DSP Digital Audio Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| TAS3103DBTRG4 | 功能描述:音频 DSP Digital Audio Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| TAS3103EVM | 功能描述:音频 DSP TAS3103 Eval Mod RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| TAS3103IDBT | 功能描述:音频 DSP Digital Audio Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| TAS3103IDBTR | 功能描述:音频 DSP Digital Audio Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。