参数资料
型号: TAS5076PFC
厂商: TEXAS INSTRUMENTS INC
元件分类: 消费家电
英文描述: SPECIALTY CONSUMER CIRCUIT, PQFP80
封装: GREEN, PLASTIC, TQFP-80
文件页数: 21/64页
文件大小: 873K
代理商: TAS5076PFC
Architecture Overview
22
SLES090A—November 2003—Revised January 2004
TAS5076
REGISTER
SETTING
FUNCTION
0Ch
01h
TC delay channel 1
0Dh
49h
TC delay channel 2
0Eh
91h
TC delay channel 3
0Fh
39h
TC delay channel 4
10h
21h
TC delay channel 5
11h
69h
TC delay channel 6
These values must be reprogrammed every time RESET is asserted. RESET causes default values to be
loaded.
2.4.6 ABD Delay
A 5-bit value is used to delay the A PWM signals with respect to B PWM signals. The value is the same for
all channels. It can be programmed from 0 to 31 DCLK clock cycles. The default ABD value is 20 DCLK clock
cycles (10100). This value is mask programmable.
This value can be changed at any time through the serial control interface.
The optimum value for ABD delay depends on the final system. This value can be adjusted for better
performance with regard to dynamic range and THD. It is recommended that the following ABD delay value
be set instead of the default value. The ABD delay value in conjunction with the TC delay values delivers the
best performance in the TAS50765182 EVM board.
REGISTER
SETTING
FUNCTION
12h
1Dh
ABD delay
This value must be reprogrammed every time RESET is asserted. RESET causes the default value to be
loaded.
NOTE:
The performance of a PurePath Digital
amplifier system is optimized by setting the PWM
timing based upon the type of back-end device that is used and the layout. These values are
set during initialization using the I2C serial interface.
2.4.7 PWM/H-Bridge and Discrete H-Bridge Driver Interface
The TAS5076 provides six PWM outputs, which are designed to drive switching output stages (back-ends)
in both single-ended (SE) and H-bridge (bridge-tied load) configuration. The back ends can be monolithic
power stages (such as the TAS5110) or six discrete differential power stages using gate drivers (such as the
the TAS55182) and MOSFETs in single-ended or bridged configurations.
The TAS5110 device is optimized for bridge-tied load (BTL) configurations. These devices require a pure
differential PWM signal with a third signal (VALID) to control the MUTE state. In the MUTE state, the TAS5110
OUTA and OUTB are both low.
One Channel
of TAS5076
PWM_AP
PWM_AM
VALID
TAS5110
OUTA
OUTB
AP
AM
RESET
BP
BM
Speaker
PWM_BP
PWM_BM
Figure 212. PWM Outputs and H-Bridge Driven in BTL Configuration
PurePath Digital is a trademark of Texas Instruments.
相关PDF资料
PDF描述
TAS5086DBT SPECIALTY CONSUMER CIRCUIT, PDSO38
TAS5086DBTR SPECIALTY CONSUMER CIRCUIT, PDSO38
TAS5086DBTRG4 SPECIALTY CONSUMER CIRCUIT, PDSO38
TAS5086DBTG4 SPECIALTY CONSUMER CIRCUIT, PDSO38
TAS5100AIDAPRG4 30 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32
相关代理商/技术参数
参数描述
TAS5076PFCG4 功能描述:音频 DSP 6-Ch Digital Audio PWM Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube
TAS5076PFCR 功能描述:音频放大器 6-Ch Digital Audio PWM Processor RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TAS5076PFCRG4 功能描述:音频放大器 6-Ch Digital Audio PWM Processor RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TAS5086 制造商:TI 制造商全称:Texas Instruments 功能描述:PurePath Digital TM AUDIO SIX-CHANNEL PWM PROCESSOR
TAS5086_06 制造商:TI 制造商全称:Texas Instruments 功能描述:PurePath Digital TM AUDIO SIX-CHANNEL PWM PROCESSOR