- 您现在的位置：买卖IC网 > PDF目录98160 > TAS5100ADAPRG4 (TEXAS INSTRUMENTS INC) 30 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 PDF资料下载
参数资料
| 型号： | TAS5100ADAPRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 30 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| 封装： | PLASTIC, HTSSOP-32 |
| 文件页数： | 14/15页 |
| 文件大小： | 189K |
| 代理商： | TAS5100ADAPRG4 |
TAS5100A
SLES030 FEBRUARY 2002
8
www.ti.com
device operation
power sequences
system power-up/power-down sequencing
The recommended power-up/power-down sequence is shown in Figure 3. For proper operation the RESET
signal should be kept LOW when both DVDD and output power (PVDDA1, PVDDA2, PVDDB1, and PVDDB2)
are being applied. The RESET signal should remain LOW for at least 1 ms after output power is applied.
> 1 ms
DVDD
PWDN
PVDDA1
PVDDA2
PVDDB1
PVDDB2
RESET
> 1 ms
> 100
s
For most applications, it is recommended that pin 13 (PWDN) be connected directly to pin 6 (DVDD).
Figure 3. Power-Up/Power-Down Sequence
RESET function
The device is put into a reset condition when the (active low) RESET signal is asserted. While in the reset state,
the input H-bridge control signals consisting of PWM_AP, PWM_AM, PWM_BP, and PWM_BM are ignored, and
the H-bridge MOSFETs are placed in a state where OUTPUTA and OUTPUTB are both low. Asserting the
RESET signal low also causes the short circuit protection latch to be reset. The RESET signal is normally
connected to the VALID signal from the TAS5000.
reinitialization sequence
Proper initial conditions for this device include asserting the RESET signal until the reset operation has
completed (1 ms). Additionally, when using this device with the TAS5000 controller, this function can be
accomplished by asserting the reset pin on the TAS5000 during the reset sequence (see Figure 3).
audio application considerations
power supply decoupling
Power supply decoupling and layout optimization information should be obtained by following the detailed
information in the application note SLAA117.
optimal power transfer for H-bridge
The TAS5100A is a power H-bridge that is designed to deliver 30 W/rms into loads of 4
to 8 . Rather than
requiring the usual heatsink, the package is designed to deliver this wattage by careful layout as described in
the application note SLAA117. Careful attention must be given to the value of the high-voltage power supply
level for a given load resistance. See recommended operating conditions.
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5100AIDAPR | 30 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TAS5100ADAPR | 30 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TAS5100AIDAP | 30 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TAS5100ADAP | 30 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TAS5101DAPR | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5100AIDAP | 制造商:Rochester Electronics LLC 功能描述:TAS5100AI - Bulk 制造商:Texas Instruments 功能描述: |
| TAS5100AIDAPR | 制造商:TI 制造商全称:Texas Instruments 功能描述:TRUE DIGITAL AUDIO AMPLIFIER TAS5100A PWM POWER OUTPUT STAGE |
| TAS5100AIDAPRG4 | 制造商:TI 制造商全称:Texas Instruments 功能描述:TRUE DIGITAL AUDIO AMPLIFIER TAS5100A PWM POWER OUTPUT STAGE |
| TAS5100DAP | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述: |
| TAS5101 | 制造商:TI 制造商全称:Texas Instruments 功能描述:TRUE DIGITAL STEREO AUDIO AMPLIFIER WITH PWM STEREO POWER OUTPUT STAGE |
发布紧急采购，3分钟左右您将得到回复。